manualshive.com logo in svg

NXP Semiconductors MSC8113, Reference Manual

The NXP Semiconductors MSC8113 Reference Manual is an essential resource for users of this cutting-edge product. It provides in-depth guidance on its features, functionalities, and usage. Download the manual for free from our website to maximize your understanding and optimize your experience with the MSC8113.

Share
Download
background image

SIU Programming Model

MSC8113 Reference Manual, Rev. 0

Freescale Semiconductor

4-21

SYPCR controls the system monitors, SIU software watchdog period, and bus monitor timing. 
The SYPCR is readable at any time but is writable only once after system hard reset.

PARTNUM 

16–23

Part Number
This field is mask-programmed with a code corresponding to the part number of 
the part on which the SIU is located. It helps factory test and user code that is 
sensitive to part changes. This field changes when the part number changes. For 
example, it would change if any new module is added or if the size of any memory 
module changes. It does not change if the part is changed to fix a bug in an 
existing module. 

The MSC8113 part 
number is 0x62.

MASKNUM

24–31

Mask Number
This field is mask-programmed with a code corresponding to the mask number of 
the part on which the SIU is located. It helps factory test and user code that is 
sensitive to part changes. It is programmed in a commonly changed layer and 
should be changed for all mask set changes. 

The MSC8113 initial 
mask number is 0x00.

SYPCR

System Protection Control Register

Bit

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

SWTC

Type

R/W

Reset

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

Bit

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

BMT

PBME LBME

—

SWE SWRI SWP

Type

R/W

Reset

1

1

1

1

1

1

1

1

0

0

0

0

0

SWTE

1

1

Table 4-8.  SYPCR Bit Descriptions

Name

Reset

Description

Settings

SWTC

0–15

1

Software Watchdog Timer Count
Contains the count value for the SIU software watchdog 
timer.

BMT

16–23

1

Bus Monitor Timing
Defines the time-out period for the bus monitor. The 
granularity of this field is 8 bus clocks. (BMT = 0xFF is 
translated to 0x7F8 clock cycles). BMT is used in both 
the system and local bus monitors.

Note:

The value 0 is invalid; an error is generated for 
each bus transaction.

PBME

24

0

System Bus Monitor Enable

0  System bus monitor is disabled.

1

System bus monitor is enabled. 

LBME

25

0

Local Bus Monitor Enable

0

Local bus monitor is disabled.

1

Local bus monitor is enabled.

Table 4-7.  IMMR Bit Descriptions (Continued)

Bits

Description

Settings

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8113

Xinje XS Series User Manual preview
XS Series
Brand: Xinje Pages: 57
Quatech DS-3000 User Manual preview
DS-3000
Brand: Quatech Pages: 27
RadiSys EPC-31 Hardware Reference Manual preview
EPC-31
Brand: RadiSys Pages: 44
Idis DR-8400 Installation Manual preview
DR-8400
Brand: Idis Pages: 31
ZALMAN CNPS6500B-AlCu User Manual preview
CNPS6500B-AlCu
Brand: ZALMAN Pages: 4
addlink SPIDER N4 Installation Manual preview
SPIDER N4
Brand: addlink Pages: 9
SIIG 1394 Dual-Port CardBus Quick Installation Manual preview
1394 Dual-Port CardBus
Brand: SIIG Pages: 8
Lanner FW-7551 User Manual preview
FW-7551
Brand: Lanner Pages: 38
AXIOMTEK CEM500 Quick Installation Manual preview
CEM500
Brand: AXIOMTEK Pages: 2
IFM QHA200 Instructions For Setup preview
QHA200
Brand: IFM Pages: 12
Net Optics Phantom HD Quick Install Manual preview
Phantom HD
Brand: Net Optics Pages: 2
Azoteq IQ Switch ProxSense RS100 Application Notes preview
IQ Switch ProxSense RS100
Brand: Azoteq Pages: 9
Paradyne Application Module 9109 OCU-DP Installation Instructions Manual preview
Application Module 9109 OCU-DP
Brand: Paradyne Pages: 8
FiberHome AN5506-04 Series Product Manual preview
AN5506-04 Series
Brand: FiberHome Pages: 146
PairGain 150-1504-15 Manual preview
150-1504-15
Brand: PairGain Pages: 68
iSMA SfAR-S-6RO User Manual preview
SfAR-S-6RO
Brand: iSMA Pages: 19
IEI Technology ECN-360A-D2550 User Manual preview
ECN-360A-D2550
Brand: IEI Technology Pages: 141
Cambium Networks PMP 450d Series User Manual preview
PMP 450d Series
Brand: Cambium Networks Pages: 215

Brands by name

Popular brands

Load more brands