NXP Semiconductors MSC8113 Reference Manual Download Page 531 | Manualshive

Page: 531 / 1202

background image

DMA Transfer Programming

MSC8113 Reference Manual, Rev. 0

Freescale Semiconductor

16-33

16.3.2 DMA Data Transfer Examples

Typical DMA programming schemes include the following:

Simple buffer transfer from a system bus external peripheral to internal memory on the
local bus

Cyclic block transfer from system bus external memory to internal memory on the local
bus

Continuous block transfer from an external peripheral to internal memory on the local bus

Simple buffer transfer from M2 to M1 on the local bus in Flyby mode

Note:

Refer to Section 16.4, DMA Programming Model, on page 16-34 for DMA controller
register descriptions. For details on programming a base address, see Section 12.8,
Memory Controller Programming Model, on page 12-95.

16.3.3 Terminating a DMA Transfer

To stop the DMA transfer temporarily, set the DCHCR[FRZ] bit. When set, this bit masks
requests assigned to the specific channel and the requestor is not serviced. All other internal
states are unaffected, so clearing this bit resumes DMA transfer without loss of data or requests.
Because the DMA controller uses pipelining, up to 96 bytes can remain in the channel FIFO and
not be delivered to the destination. This data is transferred when the channel is enabled. A DMA
channel is terminated externally either when the peripheral asserts the

DONE

signal or you clear

the DCHCR[ACTV] bit.

Either source channel or destination channel can be terminated. Termination of the source (read)
channel proceeds as follows:

1.

The DMA controller ignores any further requests from the peripheral.

2.

All the data in the FIFO is transferred to the destination channel (flushed).

3.

If transfer size is bigger than the data stored in the FIFO, additional data is flushed.

4.

DCPRAM[BD_SIZE] and DCPRAM[BD_ADDR] are updated to the correct size and
address of the buffer serviced by the DMA until the source channel is terminated.

5.

If enabled, an interrupt is generated after the last data is written to the destination
channel.

6.

The DCHCR[ACTV] bit of the destination is not cleared. You must clear the channel
before reusing it.

Termination of the destination (write) channel proceeds as follows:

1.

The DMA controller ignores any further requests from the peripheral.

2.

Tasks in progress — bus data phase, bus address phase, and pending phase — are
flushed.

«
...
529
530
531
532
533
...
»

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8113

Brand: Garmin Pages: 2

Brand: Qualys Pages: 2

Pixie-4 Express

Brand: XIA Pages: 17

Brand: Vivotek Pages: 136

Brand: GAMDIAS Pages: 15

Brand: WHOOP Pages: 26

Thin Client US310e

Brand: NEC Pages: 6

Brand: Qlogic Pages: 8

Brand: ZALMAN Pages: 5

RouterBOARD 411R

Brand: 4gon Pages: 2

Brand: IBASE Technology Pages: 39

Brand: Quantum Pages: 7

AT32F421 Series

Brand: ARTERY Pages: 337

Brand: National Instruments Pages: 80

Brand: Advantech Pages: 108

Brand: MSNswitch Pages: 2

Brand: EZCast Pro Pages: 4

Brand: ekwb Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands