manualshive.com logo in svg

NXP Semiconductors MSC8113, Reference Manual

The NXP Semiconductors MSC8113 Reference Manual is an essential resource for users of this cutting-edge product. It provides in-depth guidance on its features, functionalities, and usage. Download the manual for free from our website to maximize your understanding and optimize your experience with the MSC8113.

Share
Download
background image

MSC8113 Reference Manual, Rev. 0

6-4

Freescale Semiconductor

Boot Program

The master device is identified by one of the following fields:

„

DSI Chip ID Register (DCIR), Chip ID Value field (see Section 14.5)

„

ISBSEL field in the Exception and Mode Register (EMR), which resides in the SC140 
core Program Control Unit (see the SC140 DSP Core Reference Manual and Table 2-1).

„

ISB field in the SIU IMMR (see Section 4.2.1).

When the MSC8113 device boots from an external memory device, the user boot program 
typically does the following:

„

Writes a loader program to the internal memory. This program loads code and data to the 
internal RAM, thus enabling faster loading of code and data to the internal memory.

„

Signals SC140 cores 1, 2, and 3 to initiate a jump to address 0x0 for the M1 memory of 
SC140 cores 1, 2, and 3 by asserting VIRQ[9, 17, 25] for those SC140 cores (see the 
discussion of the Virtual Interrupt Generation Register (VIGR) in Section 17.3).

6.3 Booting from an External Host (DSI or System Bus) 

When the MSC8113 is booted from an external host, the host waits for the MSC8113 boot 
program to finish its default initialization and then initializes the device by typically loading code 
and data to the internal memory according to the memory map shown in Figure 8-2, Host on the 
System Bus Memory Map View Example, on page 8-4. The external host should poll the Valid bit 
(V) of the BR10 register. The valid bit is set when the MSC8113 boot code finishes the default 
initialization and the external host can access the internal resources, including internal memory. 
When the external host finishes its initialization sequence, it should notify the MSC8113 by 
asserting the virtual interrupt 1 (VIRQ1) to SC140 core 0, which in turn signals all the other 
SC140 cores to jump to address 0x0 of their M1 memory. The user boot program running from 
the external host typically does the following:

„

Waits for Valid bit of Bank 10 (BR10) to be set, see Section 12.8.

„

Loads code and data to internal RAM.

„

Signals SC140 core 0 to initiate a jump to address 0x0 for all SC140 cores M1. Memory 
by asserting VIRQ1 for Core 0 (see VIGR in Section 17.3).

6.4 Booting From the TDM Interface

In a system that boots from the TDM interface, a TDM boot master device writes blocks of code 
and data into the memories of multiple MSC8113 devices as illustrated in Figure 6-1 and 
according to the memory map shown in Figure 8-6. Two layered protocols are defined: a TDM 
physical layer, and a TDM logical layer handshake. The valid bit of Bank 10 (BR10) is asserted 
at the end of the TDM session.

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8113

Barracuda Networks Network Quick Start Manual preview
Network
Brand: Barracuda Networks Pages: 2
D-Link DXS-3610-54S Quick Installation Manual preview
DXS-3610-54S
Brand: D-Link Pages: 38
D-Link Web Smart DES-1210-28P Selection Manual preview
Web Smart DES-1210-28P
Brand: D-Link Pages: 6
D-Link xStack Storage DSN-4000 Series Manual preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 23
D-Link Express EtherNetwork DI-604 Brochure preview
Express EtherNetwork DI-604
Brand: D-Link Pages: 7
D-Link xStack Storage DSN-4000 Series Cli User'S Manual preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 97
Xinje XS Series User Manual preview
XS Series
Brand: Xinje Pages: 57
Ebyte E103-W13 User Manual preview
E103-W13
Brand: Ebyte Pages: 14
Lanner NCA-4035 User Manual preview
NCA-4035
Brand: Lanner Pages: 109
Internet Security Systems Proventia A1204 User Manual preview
Proventia A1204
Brand: Internet Security Systems Pages: 42
Neo Instruments Mini Vent User Manual preview
Mini Vent
Brand: Neo Instruments Pages: 2
ADC HiGain H2TU-R-402 List 7A Quick Installation preview
HiGain H2TU-R-402 List 7A
Brand: ADC Pages: 7
Renesas H8S/2633 User Manual preview
H8S/2633
Brand: Renesas Pages: 28
XJTAG XJLink2-CFM User Manual preview
XJLink2-CFM
Brand: XJTAG Pages: 9
Xilinx Zynq-7000 Manual preview
Zynq-7000
Brand: Xilinx Pages: 8
Renesas R0E001000ACB00 User Manual preview
R0E001000ACB00
Brand: Renesas Pages: 4
Z-Wave IOMOD10F Hardware User Manual preview
IOMOD10F
Brand: Z-Wave Pages: 42
National Instruments PCI-6601 User Manual preview
PCI-6601
Brand: National Instruments Pages: 52

Brands by name

Popular brands

Load more brands