manualshive.com logo in svg

NXP Semiconductors MSC8113, Reference Manual

The NXP Semiconductors MSC8113 Reference Manual is an essential resource for users of this cutting-edge product. It provides in-depth guidance on its features, functionalities, and usage. Download the manual for free from our website to maximize your understanding and optimize your experience with the MSC8113.

Share
Download
background image

MSC8113 Reference Manual, Rev. 0

3-16

Freescale Semiconductor

External Signals

3.5 Memory Controller Signals

Refer to the Memory Controller chapter in the MSC8113 Reference Manual for details on 
configuring these signals.

Table 3-6.  Memory Controller Signals  

Signal Name

Type

Description

BCTL0

Output

System Bus Buffer Control 0
Controls buffers on the data bus. Usually used with BCTL1. The exact function of this pin is 
defined by the value of SIUMCR[BCTLC]. 

BCTL1

CS5

Output

Output

System Bus Buffer Control 1
Controls buffers on the data bus. Usually used with BCTL0. The exact function of this pin is 
defined by the value of SIUMCR[BCTLC]. 

System and Local Bus Chip Select 5
Enables specific memory devices or peripherals connected to MSC8113 buses.

BM[0–2]

TC[0–2]

BNKSEL[0–2]

Input

Input/ 

Output

Output

Boot Mode 0–2
Defines the boot mode of the MSC8113. This signal is sampled on PORESET deassertion.

Transfer Code 0–2
The bus master drives these pins during the address tenure to specify the type of the code. 

Bank Select 0–2
Selects the SDRAM bank when the MSC8113 is in 60x-compatible bus mode.

ALE

Output

Address Latch Enable
Controls the external address latch used in an external master bus.

PWE[0–3]

PSDDQM[0–3]

PBS[0–3]

Output

Output

Output

System Bus Write Enable
Outputs of the bus general-purpose chip-select machine (GPCM). These pins select byte 
lanes for write operations.

System Bus SDRAM DQM
From the SDRAM control machine. These pins select specific byte lanes of SDRAM devices.

System Bus UPM Byte Select
From the UPM in the memory controller, these signals select specific byte lanes during 
memory operations. The timing of these pins is programmed in the UPM. The actual driven 
value depends on the address and size of the transaction and the port size of the accessed 
device.

PSDA10

PGPL0

Output

Output

System Bus SDRAM A10
From the bus SDRAM controller. The precharge command defines which bank is 
precharged. When the row address is driven, it is a part of the row address. When column 
address is driven, it is a part of column address.

System Bus UPM General-Purpose Line 0
One of six general-purpose output lines from the UPM. The values and timing of this pin are 
programmed in the UPM.

PSDWE

PGPL1

Output

Output

 System Bus SDRAM Write Enable
From the bus SDRAM controller. Should connect to SDRAM WE input.

 System Bus UPM General-Purpose Line 1
One of six general-purpose output lines from the UPM. The values and timing of this pin are 
programmed in the UPM.

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8113

Clavister NetWall W20A Getting Started Manual preview
NetWall W20A
Brand: Clavister Pages: 89
Xantech CC12 Installation Instructions preview
CC12
Brand: Xantech Pages: 4
IndigoVision Compact NVR-AS 4000 User Manual preview
Compact NVR-AS 4000
Brand: IndigoVision Pages: 38
AMD Geode LE-366 User Manual preview
Geode LE-366
Brand: AMD Pages: 45
Intel IXP45X Developer'S Manual preview
IXP45X
Brand: Intel Pages: 958
AMX AXB-PSCV Dimensional Drawing preview
AXB-PSCV
Brand: AMX Pages: 1
ADTRAN EXPRESS 6503 User Manual preview
EXPRESS 6503
Brand: ADTRAN Pages: 20
Supero AOC-1UIPMI-B User Manual preview
AOC-1UIPMI-B
Brand: Supero Pages: 53
Cooler Master Masterliquid ML240L RGB Manual preview
Masterliquid ML240L RGB
Brand: Cooler Master Pages: 18
TDK Powereta iQP Series Product Brief preview
Powereta iQP Series
Brand: TDK Pages: 2
Cypress Semiconductor CY7C1381DV25 Specification Sheet preview
CY7C1381DV25
Brand: Cypress Semiconductor Pages: 28
IMC Networks Wireless Outdoor Bridge XI-1500-IH Quick Installation Manual preview
Wireless Outdoor Bridge XI-1500-IH
Brand: IMC Networks Pages: 13
Cooler Master MCY-C3P1-KWNN Manual preview
MCY-C3P1-KWNN
Brand: Cooler Master Pages: 4
Lanpro LP-F22 Series Assembling Instructions preview
LP-F22 Series
Brand: Lanpro Pages: 3
Lefroy Brooks M1-5100 Installation, Operating, & Maintenance Instructions preview
M1-5100
Brand: Lefroy Brooks Pages: 10
SIIG ExpressCard 11-in-1 Reader/Writer Quick Installation Manual preview
ExpressCard 11-in-1 Reader/Writer
Brand: SIIG Pages: 8
Disc Makers ElitePro User Manual preview
ElitePro
Brand: Disc Makers Pages: 12
WiebeTech FCDKV4 User Manual preview
FCDKV4
Brand: WiebeTech Pages: 8

Brands by name

Popular brands

Load more brands