manualshive.com logo in svg

NXP Semiconductors MSC8113, Reference Manual

The NXP Semiconductors MSC8113 Reference Manual is an essential resource for users of this cutting-edge product. It provides in-depth guidance on its features, functionalities, and usage. Download the manual for free from our website to maximize your understanding and optimize your experience with the MSC8113.

Share
Download
background image

Ethernet Controller Programming Model

MSC8113 Reference Manual, Rev. 0

Freescale Semiconductor

25-73

OSTBD is the out-of-sequence TxBD register, which includes the status/control and data length 
in the same format as a regular TxBD. It is useful for sending flow control frames. The 
OSTBD[R] is always checked between frames. If it is not ready, a regular frame is sent. You 
must set OSTBD[L] while preparing this BD. If a flow control frame is sent and OSTBD[I] is set, 
a TXC event is generated after frame transmission. This register must be cleared while not in use. 
When the Ethernet controller is in pause mode, the out-of-sequence BD cannot be used to send 
another flow control frame because the MAC regards it as a regular TxBD. 

OSTBD

Out-of-Sequence TxBD Register

Bit

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

PAD

W

I

L

TC

DEF

—

LC

RL

RC

UN

—

Type

R/W

R

Reset

0

0

0

0

1

0

0

0

0

0

0

0

0

0

0

0

Bit

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

OSTBDLEN

Type

R/W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Table 25-44.  OSTBD Bit Descriptions

Bit

Reset

Description

Settings

R

0

0

Ready
Indicates whether the data buffer associated with a BD is ready 
for transmission. When this bit is cleared, you can 
manipulate this BD or its associated data buffer. The Ethernet 
controller clears this bit after the buffer is transmitted or after 
an error condition is encountered.
When this bit is set, you cannot write to any fields of this BD.
This bit is written by the Ethernet controller and the user.

0

The data buffer associated with 
this BD is not ready for 
transmission. 

1

The data buffer that the user 
has prepared for transmission 
was not transmitted or is 
currently being transmitted. 

PAD

1

0

Padding for Short Frames
Enables/disables padding for short frames. This bit is cleared 
only while one TxBD is used (L is set) and the 
MACCFG2R[PADCRC, CRCEN] bits are cleared. Otherwise, 
pads are added to short frames. When PAD is set, padding 
bytes are inserted until the length of the transmitted frame 
equals 64 bytes. Unlike the MPC8260 device, which pads up to 
the MINFLR value, the Ethernet controller always pads up to 
the IEEE minimum frame length of 64 bytes.

0

Do not add padding to short 
frames unless TxBD[TC] is set.

1

Add padding to short frames.

W

2

0

Wrap
Wrap, written by user. This bit is ignored by the Ethernet 
controller.

0

The next BD is found in the 
consecutive location

1

The next BD is found at the 
location defined by the user.

I

3

0

Interrupt
Causes an interrupt if IEVENT[TXFEN] is enabled.
This bit is written by user.

0

No interrupt is generated after 
this buffer is serviced.

1

IEVENT[TXF] is set after this 
buffer is serviced. 

L
4

1

Last in Frame
The OSTBD is always the last in the frame, so L is always set. 
This bit is hardwired to a value of 1

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8113

Yaesu FT-817 - Modification Instructions preview
FT-817 -
Brand: Yaesu Pages: 2
D-Link AirPlus XtremeG Ethernet-to-Wireless Bridge... Manual preview
AirPlus XtremeG Ethernet-to-Wireless Bridge...
Brand: D-Link Pages: 31
WHOOP WHT-25LT Quick Start Manual preview
WHT-25LT
Brand: WHOOP Pages: 26
EMCIS LISN User'S Operating Manual preview
LISN
Brand: EMCIS Pages: 14
Glacier G2080TiFE Installation Manual preview
G2080TiFE
Brand: Glacier Pages: 2
Idis DR-2308P Quick Manual preview
DR-2308P
Brand: Idis Pages: 18
TANDBERG 240LTO Quick Start Manual preview
240LTO
Brand: TANDBERG Pages: 2
Kentrox RMM-1400 Configuration Manual preview
RMM-1400
Brand: Kentrox Pages: 246
Datalogic C-BOX 100 Instruction Manual preview
C-BOX 100
Brand: Datalogic Pages: 2
Valcom VIP-814 Installation Manual preview
VIP-814
Brand: Valcom Pages: 3
YASKAWA 040-1CA00 Manual preview
040-1CA00
Brand: YASKAWA Pages: 87
ICS Advent PCI-COM485/8 Product Manual preview
PCI-COM485/8
Brand: ICS Advent Pages: 26
ADTRAN NetVanta 1224 Quick Start Manual preview
NetVanta 1224
Brand: ADTRAN Pages: 2
ADTRAN 1200934L1 Installation Instructions preview
1200934L1
Brand: ADTRAN Pages: 2
ADTRAN 17005660F1 Quick Start preview
17005660F1
Brand: ADTRAN Pages: 4
ADTRAN 1442823F1 Quick Start Manual preview
1442823F1
Brand: ADTRAN Pages: 4
ADTRAN NetVanta Series Quick Configuration Manual preview
NetVanta Series
Brand: ADTRAN Pages: 7
ADTRAN NetVanta 2000 Series Quick Start Manual preview
NetVanta 2000 Series
Brand: ADTRAN Pages: 15

Brands by name

Popular brands

Load more brands