manualshive.com logo in svg

NXP Semiconductors MSC8113, Reference Manual

The NXP Semiconductors MSC8113 Reference Manual is an essential resource for users of this cutting-edge product. It provides in-depth guidance on its features, functionalities, and usage. Download the manual for free from our website to maximize your understanding and optimize your experience with the MSC8113.

Share
Download
background image

SIU Programming Model

MSC8113 Reference Manual, Rev. 0

Freescale Semiconductor

4-11

Reconfiguring BCR modifies system and local bus behavior and can result in unexpected results 
if there are currently active accesses. Therefore, execute code that modifies the BCR only from 
internal memory. Also, execute a write to the BCR when only one core is active and there are no 
active DMA transfers.

Table 4-3.  BCR Bit Descriptions

Name

Description

Settings

EBM

0

External Bus Mode
Selects the bus mode. For details, refer to Section 
13.2.1, System Bus Operating Modes. The initial value is 
selected by the Hard Reset Configuration Word (HRCW) 
EBM bit. See Section 5.6.1 for details.

0

Single MSC8113 bus mode.

1

Multi-master bus mode.

APD

1–3

Address Phase Delay
Specifies the minimum number of address tenure wait 
states for address operations initiated by a 
60x-compatible system bus master. APD indicates how 
many cycles the MSC8113 should wait for ARTRY, but 
because ARTRY can be asserted (by other masters) only 
on cacheable address spaces, APD is considered only on 
transactions that hit one of the 60x-assigned memory 
controller banks and have the GBL signal asserted during 
address phase.

—

4–7

Reserved. Write to zero for future compatibility.

PLDP

8

Pipeline Maximum Depth
See Section 13.2.3.12, Pipeline Control.

0

Pipeline maximum depth is one.

1

Pipeline maximum depth is zero.

DSBI

9

Disable System Bus on Internal Access
Determines which internal system bus lines are reflected 
on the external system bus.
Note:

Address attribute lines are always reflected on 
the external system bus.

0

Data and address lines for internal system bus 
transfers are reflected on the external system 
bus.

1

Depends on the value of EBM, as follows:

•  If EBM = 0, neither data nor address lines for 

internal system bus transfers are reflected on the 
external system bus.

•  If EBM = 1, only address lines for internal system 

bus transfers are reflected on the external system 
bus.

10

Reserved. Write to zero for future compatibility.

EAV

11

Enable Address Visibility
Normally, when the MSC8113 is in single-MSC8113 bus 
mode, the bank select signals for SDRAM accesses are 
multiplexed on the system bus address lines. Therefore, 
for SDRAM accesses, the internal address is not visible 
for debug purposes. However the bank select signals can 
also be driven on dedicated lines (see SIUMCR[TCPC]). 
In this case, EAV is used to force address visibility. 

0

Bank select signals are driven on system bus 
address lines. There is no full address visibility.

1

Bank select signals are not driven on address 
bus. During READ and WRITE commands to 
SDRAM devices, the full address is driven on 
system bus address lines.

ETM

12

System Bus Compatibility Mode Enable
See Section 13.2.3.8, Extended Transfer Mode. This bit 
also enables data streaming mode; see Section 13.2.4.2, 
Data Streaming Mode for details.

0

Strict 60x system bus mode. Extended transfer 
mode is disabled. 

1

Extended transfer mode is enabled.

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8113

National Instruments NI 9213 Getting Started preview
NI 9213
Brand: National Instruments Pages: 11
Wintech TDS510USB Plus Installation Manual preview
TDS510USB Plus
Brand: Wintech Pages: 21
Lanner ICS-P570 User Manual preview
ICS-P570
Brand: Lanner Pages: 63
Waves MaxxBCL Manual preview
MaxxBCL
Brand: Waves Pages: 41
Renesas Converter Board R0E5212BACFG00 User Manual preview
Converter Board R0E5212BACFG00
Brand: Renesas Pages: 6
C&T Solution VCO-6131E-4M2 User Manual preview
VCO-6131E-4M2
Brand: C&T Solution Pages: 129
Element14 Wireless Connectivity Cape Quick Start Manual preview
Wireless Connectivity Cape
Brand: Element14 Pages: 2
XtendLan XL-HCW224C User Manual preview
XL-HCW224C
Brand: XtendLan Pages: 52
mikroElektronika Pressure click Quick Start Manual preview
Pressure click
Brand: mikroElektronika Pages: 2
Vega ARIES v3.0 Product Reference Manual preview
ARIES v3.0
Brand: Vega Pages: 12
netsys NVF-2400S User Manual preview
NVF-2400S
Brand: netsys Pages: 164
Spirent A2-400 Installation Instructions Manual preview
A2-400
Brand: Spirent Pages: 22
ETAS ES1392.1 User Manual preview
ES1392.1
Brand: ETAS Pages: 36
FOLSOM Blend PRO BP-2002 Installation And Operator'S Manual preview
Blend PRO BP-2002
Brand: FOLSOM Pages: 89
c SwiftreaderX Installation Manual preview
SwiftreaderX
Brand: c Pages: 32
QNAP QSW-3216R-8S8T Quick Installation Manual preview
QSW-3216R-8S8T
Brand: QNAP Pages: 11
Qorvo QPE6105A Manual preview
QPE6105A
Brand: Qorvo Pages: 15
NetApp NS224 Instructions Manual preview
NS224
Brand: NetApp Pages: 28

Brands by name

Popular brands

Load more brands