manualshive.com logo in svg

NXP Semiconductors MSC8113, Reference Manual

The NXP Semiconductors MSC8113 Reference Manual is an essential resource for users of this cutting-edge product. It provides in-depth guidance on its features, functionalities, and usage. Download the manual for free from our website to maximize your understanding and optimize your experience with the MSC8113.

Share
Download
background image

Instruction Cache (ICache)

MSC8113 Reference Manual, Rev. 0

Freescale Semiconductor

9-33

The ICache has only one set of LRU boundaries (upper and lower) that are programmed in only 
one register, and each task should change these boundaries to enable all multi-task support:

„

Flexible boundaries. Most suitable for the single-stack OS model.

„

Fixed allocation. Most suitable for the multi-stack OS model.

„

Full cache shared for all tasks. May be associated with extensive thrashing cost.

9.4.4   ICache Programming Model

ICache programming refers to all memory accesses that can occur to the memory-mapped 
registers of the ICache. This section summarizes the different accesses, their functionality in the 
ICache, and restrictions. Notice that debug reads and commands are described in detail in Section 
9.4.2, Debugging. The cache is programmed and read through the QBus. It acts as a 
zero-wait-state slave on QBus Bank 0, sharing it with other peripherals similarly connected (for 
example, the PIC). Bank 0 always has an immediate attribute, thus preventing ICache commands 
and mode changes from being randomly delayed by the write buffer and taking effect at 
unexpected times. Through the programming interface, you can set cache modes, send 
commands to the ICache, and read ICache registers.

Figure 9-12.  Cache Support in Run-Time Multi-tasking

Flexible LRU Boundaries

Fixed Allocation

Time

Boundary

Active

Task 2

Task 3

Task 1

Cache

Boundary

Active

Cache

Task 4

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8113

Commell LS-570 User Manual preview
LS-570
Brand: Commell Pages: 58
Delta M125HV-113 Quick Installation Manual preview
M125HV-113
Brand: Delta Pages: 2
Renesas Compact Emulator M30620T-CPE User Manual preview
Compact Emulator M30620T-CPE
Brand: Renesas Pages: 52
RAK RAK3372 Quick Start Manual preview
RAK3372
Brand: RAK Pages: 30
Dantel 46020-38 Installation & Operation Manual preview
46020-38
Brand: Dantel Pages: 62
Juniper NFX250 Quick Start Manual preview
NFX250
Brand: Juniper Pages: 7
addlink SPIDER N4 Installation Manual preview
SPIDER N4
Brand: addlink Pages: 9
SIIG 1394 Dual-Port CardBus Quick Installation Manual preview
1394 Dual-Port CardBus
Brand: SIIG Pages: 8
ZALMAN ZM80C-HP Manual preview
ZM80C-HP
Brand: ZALMAN Pages: 18
Corsair H80i v2 Quick Start Manual preview
H80i v2
Brand: Corsair Pages: 12
Alesis QuadraVerb 2 Setting Up preview
QuadraVerb 2
Brand: Alesis Pages: 11
Wistron NeWeb DNBA-81 User Manual preview
DNBA-81
Brand: Wistron NeWeb Pages: 32
Intel 2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 1 01-2011 Datasheet preview
2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 1 01-2011
Brand: Intel Pages: 172
AXIOMTEK IPC934-230-FL Quick Installation Manual preview
IPC934-230-FL
Brand: AXIOMTEK Pages: 2
Hameg HM6050-2K Manual preview
HM6050-2K
Brand: Hameg Pages: 46
FabiaTech FB2701 User Manual preview
FB2701
Brand: FabiaTech Pages: 86
National Instruments GPIB-120A User Manual preview
GPIB-120A
Brand: National Instruments Pages: 36
ADTRAN NetVanta 3430 Manual preview
NetVanta 3430
Brand: ADTRAN Pages: 2

Brands by name

Popular brands

Load more brands