manualshive.com logo in svg

NXP Semiconductors MSC8113, Reference Manual

The NXP Semiconductors MSC8113 Reference Manual is an essential resource for users of this cutting-edge product. It provides in-depth guidance on its features, functionalities, and usage. Download the manual for free from our website to maximize your understanding and optimize your experience with the MSC8113.

Share
Download
background image

System Bus Signals

MSC8113 Reference Manual, Rev. 0

Freescale Semiconductor

13-13

TA

Input/

Output

Input

Output

Transfer Acknowledge

State Meaning

Asserted. Indicates that a single-beat data transfer completed successfully or 
that a data beat in a burst transfer completed successfully. Note that TA must 
be asserted for each data beat in a burst transaction. For more information, 
see Section 13.2.4.3, Data Bus Transfers and Normal Termination.
Deasserted. (During assertion of DBB) indicates that, until TA is asserted, the 
MSC8113 must continue to drive the data for the current write or must wait to 
sample the data for reads.

Timing Comments

Assertion. Must not occur before the cycle after the assertion of AACK for the 
current transaction if the address retry mechanism is to be used to prevent 
invalid data from being used by the MSC8113. Otherwise, assertion may 
occur at any time during the assertion of DBB. The system can withhold 
assertion of TA to indicate that the MSC8113 should insert wait states to 
extend the duration of the data beat.
Deassertion. Must occur after the bus clock cycle of the final (or only) data 
beat of the transfer. For a burst transfer, the system can assert TA for one bus 
clock cycle and then deassert it to advance the burst transfer to the next beat 
and insert wait states during the next beat. 

State Meaning

Asserted. Indicates that the data has been latched for a write operation, or 
that the data is valid for a read operation, thus terminating the current data 
beat. If it is the last or only data beat, this also terminates the data tenure. 
Deasserted. Indicates that master must extend the current data beat (insert 
wait states) until data can be provided or accepted by the MSC8113 device. 

Timing Comments

Assertion. Occurs on the clock in which the current data transfer can be 
completed. 
Deassertion. Occurs after the clock cycle of the final (or only) data beat of the 
transfer. For a burst transfer, TA may be deasserted between beats to insert 
one or more wait states before the completion of the next beat.

TEA

Input/Outp

ut

Input

Output

Transfer Error Acknowledge

State Meaning

Asserted. Indicates that a bus error occurred. The assertion of TEA causes 
the deassertion/high impedance of DBB in the next clock cycle. However, 
data entering the MSC8113 internal memory resources such as GPRs or 
caches are not invalidated. 
Deasserted. Indicates that no bus error was detected. 

Timing Comments

Assertion. May be asserted while DBB is asserted and for the cycle after if TA 
is asserted during a read operation. TEA should be asserted for one cycle 
only. 
Deassertion. TEA must be deasserted no later than the deassertion of DBB.

State Meaning

Asserted. Indicates that a bus error has occurred. Assertion of TEA 
terminates the transaction in progress; that is, asserting TA is unnecessary 
because it is ignored by the target device. An unsupported memory 
transaction, such as a direct-store access or a graphics read or write, causes 
the assertion of TEA (provided TEA is enabled and the address transfer 
matches the MSC8113 memory map). 
Deasserted. Indicates that no bus error was detected.

Timing Comments

Assertion. Occurs on the first clock after the bus error is detected.
Deassertion. Occurs one clock after assertion.

Table 13-9.  Data Transfer Termination Signals (Continued)

Name

Type

Description

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8113

Keithley 7707 User Manual preview
7707
Brand: Keithley Pages: 59
Opvimus UMX-ETH+ Operating Instructions Manual preview
UMX-ETH+
Brand: Opvimus Pages: 12
National Instruments NI-9252 Calibration Procedure preview
NI-9252
Brand: National Instruments Pages: 9
Aleratec 310108 Quick Start Manual preview
310108
Brand: Aleratec Pages: 12
hawa HAWA-Frontside 60/B Planning And Installation Instructions preview
HAWA-Frontside 60/B
Brand: hawa Pages: 28
Acqiris SA217P Startup Manual preview
SA217P
Brand: Acqiris Pages: 22
Ruckus Wireless SmartZone 3.6 Command Reference Manual preview
SmartZone 3.6
Brand: Ruckus Wireless Pages: 102
Cypress Semiconductor CY7C1019D Specification Sheet preview
CY7C1019D
Brand: Cypress Semiconductor Pages: 11
Keithley PDISO-8 User Manual preview
PDISO-8
Brand: Keithley Pages: 71
WAGO 750-459 Manual preview
750-459
Brand: WAGO Pages: 48
VCS VIP 1000 User Manual preview
VIP 1000
Brand: VCS Pages: 118
Observint NVR16 Firmware User Manual preview
NVR16
Brand: Observint Pages: 117
Abit G740A Installation Manual And User'S Manual preview
G740A
Brand: Abit Pages: 22
Hafele Suzie-Q 541.35.520 Mounting Instructions preview
Suzie-Q 541.35.520
Brand: Hafele Pages: 12
Navitar 1-62645 Dimensional Drawing preview
1-62645
Brand: Navitar Pages: 1
Boss Vocal Performer VE-20 Owner'S Manual preview
Vocal Performer VE-20
Brand: Boss Pages: 20
Renesas Protection Board R0E330850ACBP0 User Manual preview
Protection Board R0E330850ACBP0
Brand: Renesas Pages: 8
QSC Q-SYS QIO-GP8x8 Hardware User Manual preview
Q-SYS QIO-GP8x8
Brand: QSC Pages: 13

Brands by name

Popular brands

Load more brands