manualshive.com logo in svg

NXP Semiconductors MSC8113, Reference Manual

The NXP Semiconductors MSC8113 Reference Manual is an essential resource for users of this cutting-edge product. It provides in-depth guidance on its features, functionalities, and usage. Download the manual for free from our website to maximize your understanding and optimize your experience with the MSC8113.

Share
Download
background image

MSC8113 Reference Manual, Rev. 0

18-10

Freescale Semiconductor

Debugging

The number of bits in this stream, that is, the number of clocks in this state, is equal to the number 
of selected SC140 cores in the cascade, which is three. This state is indicated by the 

CHOOSE_CLOCK_DR

 signal. For example, for the three SC140 cores on the MSC8113, to activate 

the third core in the cascade, which is the closest to 

TDO

 and the farthest from 

TDI

, the data is 

1,0,0,0 (first a one, then three zeros). If the data is 1,0,1,0, then both the second and the fourth 
cells are selected.

Only the EOnCE command register (ECR) should be accessed in cascaded mode. To do this, first 
enter the CHOOSE_EONCE instruction and set ENABLE_ONCE to 1 for all cores. Then shift in 
the cascaded value for all ECRs in series. When the shift is ended and the controller issues a 
SHIFT_UPDATE, all registers are updated in parallel. However, it is not guaranteed that this 
occurs in the same SC140 clock cycle for all cores.

Note:

Accessing any other EOnCE register in cascaded mode may fail. Always select a 
single core at a time to access any other EOnCE register.

18.4.2   DEBUG_REQUEST and ENABLE_EOnCE Commands

After completing the CHOOSE_EOnCE instruction, you can execute DEBUG_REQUEST and 
ENABLE_EOnCE instructions. More than one such instruction can execute, and other 
instructions can be placed between them, as well as between them and the CHOOSE_EOnCE 
instruction. The EOnCE modules selected in the CHOOSE_EOnCE instruction remain selected 
until the next CHOOSE_EOnCE instruction. The DEBUG_REQUEST or ENABLE_EOnCE 
instruction is shifted in during the 

SHIFT

-

IR

 state, as are all JTAG instructions. 

18.4.3   Reading/Writing EOnCE Registers Through JTAG

An external host can read or write almost every EOnCE register through the JTAG interface by 
performing the following steps:

1.

Execute the CHOOSE_EOnCE command in the JTAG.

2.

Send the data showing which EOnCE module is chosen. This command enables the 
JTAG to manage multiple EOnCE modules in a device.

3.

Execute the ENABLE_EOnCE command in the JTAG. 

4.

Write the EOnCE command into the EOnCE Command register (ECR); that is, enter the 
JTAG TAP state machine into the 

SHIFT

-

DR

 state and then give the required command 

on the 

TDI

 input signal. 

After the command is shifted in, the JTAG TAP state machine must enter the 

UPDATE

-

DR

 state. 

The data shifted via the 

TDI

 is sampled into the ECR. If, for example, the command written into 

the ECR is Write EDCA0_CTRL, then the host must again enter the JTAG into 

SHIFT

-

DR

 and 

shift the required data, which is to be written into the EDCA0_CTRL, via 

TDI

. If the command is 

read some register, then the DR chain must be passed again and the contents of the register are 

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8113

IBM System x3630 M4 Manual preview
System x3630 M4
Brand: IBM Pages: 7
Lab.gruppen NLB 60E Operation Manual preview
NLB 60E
Brand: Lab.gruppen Pages: 35
National Instruments NI 9426 Getting Started Manual preview
NI 9426
Brand: National Instruments Pages: 17
NXP Semiconductors MIMXRT1160 Hardware Development Manual preview
MIMXRT1160
Brand: NXP Semiconductors Pages: 24
Direct IP IDIS DR-1304P Operation Manual preview
IDIS DR-1304P
Brand: Direct IP Pages: 76
3Ware 9550SX Series Installation Manual preview
9550SX Series
Brand: 3Ware Pages: 4
TANDBERG D5018501 Hardware User Manual preview
D5018501
Brand: TANDBERG Pages: 3
Softing CAN-PRO1-PCIE Hardware User Manual preview
CAN-PRO1-PCIE
Brand: Softing Pages: 4
Valcom VIP-822A Quick Start Manual preview
VIP-822A
Brand: Valcom Pages: 4
National Instruments NI-9206 Getting Started preview
NI-9206
Brand: National Instruments Pages: 8
Crystal Vision TANDEM HD-21 User Manual preview
TANDEM HD-21
Brand: Crystal Vision Pages: 54
Z-Com ZCN-1523H-5-16 Quick Installation Manual preview
ZCN-1523H-5-16
Brand: Z-Com Pages: 18
3Com 3C433279A Release Note preview
3C433279A
Brand: 3Com Pages: 12
McIntosh MX160 Owner'S Manual preview
MX160
Brand: McIntosh Pages: 44
Wistron NeWeb DNBA-81 User Manual preview
DNBA-81
Brand: Wistron NeWeb Pages: 32
Grizzly PSJ-VZ58 gen3 OEM User Manual preview
PSJ-VZ58 gen3 OEM
Brand: Grizzly Pages: 12
Galileo Quark SoC X1000 Getting Started Manual preview
Quark SoC X1000
Brand: Galileo Pages: 20
MA Master Fader 1 User Manual preview
Master Fader 1
Brand: MA Pages: 4

Brands by name

Popular brands

Load more brands