manualshive.com logo in svg

NXP Semiconductors MSC8113, Reference Manual

The NXP Semiconductors MSC8113 Reference Manual is an essential resource for users of this cutting-edge product. It provides in-depth guidance on its features, functionalities, and usage. Download the manual for free from our website to maximize your understanding and optimize your experience with the MSC8113.

Share
Download
background image

MSC8113 Reference Manual, Rev. 0

5-14

Freescale Semiconductor

Reset

INTOUT

2

0

INT_OUT or IRQ7 Selection
Defines the initial value of SIUMCR[INTOUT]. 
See Section 4.2, SIU Programming Model.

0

IRQ7/INT_OUT is IRQ7.

1

IRQ7/INT_OUT is INT_OUT.

EBM

3

0

External Bus Mode
Defines the initial value of BCR[EBM]. See 
Section 4.2, SIU Programming Model.

0 

Single MSC8113 bus mode.

1 60x-compatible 

bus 

mode.

BPS

4–5

00

Boot Port Size
Defines the initial value of BR0[PS], the port size 
for memory controller bank 0. See Section 12.8, 
Memory Controller Programming Model.

00 64-bit port size.

01 8-bit port size.

10 16-bit port size.

11

32-bit port size.

SCDIS

6

0

SC140 Cores Disabled
Enables/disables the SC140 cores. See Chapter 
9, Extended Core. 

0 SC140 

cores 

enabled.

1 SC140 

cores 

disabled.

ISPS

7

0

Internal Space Port Size
Defines the initial value of BCR[ISPS]. Setting 
ISPS enables a 32-bit master to access the 
MSC8113 internal space. See Section 4.2, SIU 
Programming Model.

Note: When the ISPS bit is set, an external 
master can only access the MSC8113 internal 
space using 32-bit single accesses.

0

MSC8113 acts as a 64-bit slave to 
external masters access to its internal 
space.

1

MSC8113 acts as a 32-bit slave to 
external masters access to its internal 
space.

IRPC

8

0

Interrupt Pin Configuration
Defines the initial value of SIUMCR[IRPC] and 
burst address pin functionality. See Section 4.2, 
SIU Programming Model.

0

IRQ5/IRQ2/IRQ3.

1

BADDR29/BADDR30/BADDR31.

—

9

0

Reserved. Write to zero for future compatibility.

DPPC
10–11

00

Data Parity Pin Configuration
Defines the initial value of SIUMCR[DPPC] and 
DMA channel request/acknowledge pin 
functionality. See Section 4.2, SIU Programming 
Model.

00 NC/IRQ[1–7].

01 DP[0–7].

10 DREQ[1–4]/DACK[1–4].

11

EXT_BR[2–3]/EXT_BG[2–3]/ 

EXT_DBG[2–3]/IRQ[6–7].

NMI OUT

12

0

NMI OUT
Defines the host core to handle a non-maskable 
interrupt (NMI) event.

0 

NMI is serviced by SC140s.

1 

NMI is routed to NMI_OUT and 
serviced by the external host.

ISBSEL

13–15

000

Initial Internal Space Base Select
Defines the initial value of IMMR[ISB], which 
determines the base address of the internal 
memory space. See Section 4.2, SIU 
Programming Model. The SC140 internal address 
space spans from 0x00000000

–

0x00FFFFFF (16 

MB). Therefore it is not advisable to map the 
IMMR in this space, since the SC140s cannot 
access the SIU registers. See Chapter 12, 
Memory Controller.

000

0xF0000000

001

0xF0F00000

010

0xFF000000

011

0xFFF00000

100

Reserved. Do not use this option.

101

Reserved. Do not use this option.

110

0x0F000000

111

0x0FF00000

—

16

0

Reserved. Write to zero for future compatibility.

Table 5-8.  Hard Reset Configuration Word Bit Descriptions (Continued)

Name

Reset

Description

Settings

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8113

Clavister NetWall W20A Getting Started Manual preview
NetWall W20A
Brand: Clavister Pages: 89
Black Box JPM083A Manual preview
JPM083A
Brand: Black Box Pages: 9
Valcom VIP-822A Quick Start Manual preview
VIP-822A
Brand: Valcom Pages: 4
Grundig GSS STC 160 Assembly Instruction Manual preview
GSS STC 160
Brand: Grundig Pages: 24
B&B Electronics 4 Channel Input Buffer Board SDAIBB Product Manual preview
4 Channel Input Buffer Board SDAIBB
Brand: B&B Electronics Pages: 22
Nortel BayStack 660 Use Manual preview
BayStack 660
Brand: Nortel Pages: 163
Baracoda Scan Dongle User Manual preview
Scan Dongle
Brand: Baracoda Pages: 16
Anthem Audio SFD-2 MkIII Jumper Configurations preview
SFD-2 MkIII Jumper
Brand: Anthem Audio Pages: 2
Comtrend Corporation WAP-5922MP Quick Install Manual preview
WAP-5922MP
Brand: Comtrend Corporation Pages: 4
Vivint AirBridge VS-YOFIMN-000 Quick Reference preview
AirBridge VS-YOFIMN-000
Brand: Vivint Pages: 2
Renesas Protection Board R0E330850ACBP0 User Manual preview
Protection Board R0E330850ACBP0
Brand: Renesas Pages: 8
DayTronic PC-HSICA Instruction Manual preview
PC-HSICA
Brand: DayTronic Pages: 13
ZALMAN CNPS2005-Plus User Manual preview
CNPS2005-Plus
Brand: ZALMAN Pages: 6
NEC EP-753304DU-R User Manual preview
EP-753304DU-R
Brand: NEC Pages: 26
Meridian Meridian 1 Option 11C Mini Technical Reference Manual preview
Meridian 1 Option 11C Mini
Brand: Meridian Pages: 546
Cypress Semiconductor CY7C1440AV33 Specification Sheet preview
CY7C1440AV33
Brand: Cypress Semiconductor Pages: 31
Intel 80C186EC Manual preview
80C186EC
Brand: Intel Pages: 57
Exsys EX-16600 Manual preview
EX-16600
Brand: Exsys Pages: 2

Brands by name

Popular brands

Load more brands