NXP Semiconductors MSC8113 Reference Manual Download Page 309 | Manualshive

Page: 309 / 1202

background image

MSC8113 Reference Manual, Rev. 0

Freescale Semiconductor

12-1

Memory Controller

12

The MSC8113 memory controller serves two purposes:

It supports a glueless interface to external memory and peripheral devices on the external
system bus.

It enables interfacing with the IPBus peripherals and internal memories through the
internal local bus.

The memory controller controls up to eight external memory banks that are located on the
external system bus and shared by a high-performance SDRAM machine, a General-Purpose
Chip-Select Machine (GPCM), and three User-Programmable Machines (UPMs). It supports a
glueless interface to synchronous DRAM (SDRAM), SRAM, EPROM, Flash EPROM, burstable
RAM, regular DRAM devices, extended data output DRAM devices, and other peripherals. Two
additional memory banks control access to internal resources, using the internal local bus. This
flexible memory controller allows the implementation of memory systems with very specific
timing requirements:

The SDRAM machine provides an interface to synchronous DRAMs using SDRAM
pipelining, bank interleaving, and back-to-back read or write in page mode, to achieve the
highest performance.

The GPCM provides interfacing for simpler, lower-performance memory resources and
memory-mapped devices. The GPCM has inherently lower performance because it does
not support bursting. For this reason, GPCM-controlled banks are used primarily for
boot-loading and access to low-performance memory-mapped peripherals. The GPCM
controls Bank 9 to access IPBus peripherals.

The UPM supports address multiplexing of the external bus, refresh timers, and generation
of programmable control signals for row address and column address strobes to allow for a
glueless interface to DRAMs, burstable SRAMs, and almost any other kind of peripheral.
The refresh timers allow refresh cycles to be initiated. The UPM generates programmable
timing patterns to the control signals that govern a memory device. These patterns define
how the external control signals behave during a read, write, burst-read, or burst-write
access request. Refresh timers periodically generate user-defined refresh cycles. There are
three UPMs (A, B and C) in the memory controller. UPMs A and B can be assigned either
to the system bus or to the local bus. UPM C is allocated for Bank 11, which is assigned to
internal memories (M2 memory and three M1 memories).

«
...
307
308
309
310
311
...
»

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8113

Brand: TC Electronic Pages: 2

Express5800/E120d-M

Brand: NEC Pages: 2

Network Video Recorders

Brand: e-Line Technology Pages: 34

Brand: Alesis Pages: 46

Urban Wireless CC-VT240W

Brand: Cateye Pages: 15

Brand: red lion Pages: 5

TD-3316B4-16P-A1

Brand: TVT Digital Pages: 2

Brand: Lanner Pages: 59

EK-FC980 GTX Classy

Brand: ekwb Pages: 2

Brand: Xyclop Pages: 144

Brand: Silvertel Pages: 9

500 - DATASHEET REV 003

Brand: Intel Pages: 67

Brand: Nortel Pages: 163

Brand: Baracoda Pages: 16

Brand: Alcatel-Lucent Pages: 60

Brand: Taiwan Commate Computer Inc. Pages: 25

Brand: Greenlee Pages: 52

High-Precision AD/DA Board

Brand: Waveshare Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands