manualshive.com logo in svg

NXP Semiconductors MSC8113, Reference Manual

The NXP Semiconductors MSC8113 Reference Manual is an essential resource for users of this cutting-edge product. It provides in-depth guidance on its features, functionalities, and usage. Download the manual for free from our website to maximize your understanding and optimize your experience with the MSC8113.

Share
Download
background image

MSC8113 Reference Manual, Rev. 0

12-34

Freescale Semiconductor

Memory Controller

12.3.1   GPCM Signals: Timing Configuration

If BRx[MS] selects the GPCM, the attributes for the memory cycle are taken from ORx. These 
attributes include the ORx[CSNT], ORx[ACS], ORx[SCY], ORx[SETA], ORx[TRLX], and 
ORx[EHTR] fields. Table 12-16 shows signal behavior and system response.

12.3.1.1   Chip-Select Assertion Timing 

From 0 to 30 wait states can be programmed for 

PSDVAL

 generation. Byte-write enable signals 

(

PWE

) are available for each byte written to memory. Also, the output enable signal (

POE

) 

eliminates external glue logic. The memory banks selected to work with the GPCM have unique 
features. On system reset, a global (boot) chip-select provides a boot ROM chip-select before the 
system is fully configured. The banks selected to work with the GPCM support an option to 
output the 

CS

 line at different timings with respect to the external address bus. 

CS

 can be output in 

any of three configurations:

„

Simultaneous with the external address

„

One quarter of a clock cycle later

„

One half of a clock cycle later

Table 12-16.  GPCM Strobe Signal Behavior

Option Register Attributes

Signal Behavior

TRLX Access ACS

CSNT 

Address to CS 

Asserted

CS Deasserted to 

Address Change 

PWE Deasserted to 

Address/Data Invalid

Total Cycles

0

Read

00

x

0

0

x

2  +  SCY

0

Read

10

x

1/4

 × 

Clock

0

x

2 + SCY

0

Read

11

x

1/2

 × 

Clock

0

x

2 + SCY

0

Write

00

0

0

0

0

2  +  SCY

0

Write

10

0

1/4

 × 

Clock

0

0

2 + SCY

0

Write

11

0

1/2

 × 

Clock

0

0

2 + SCY

0

Write

00

1

0

0

–1/4

 × 

Clock

2 + SCY

0

Write

10

1

1/4

 × 

Clock

–1/4 

× 

Clock

–1/4

 × 

Clock

2 + SCY

0

Write

11

1

1/2

 × 

Clock

–1/4

 × 

Clock

–1/4

 × 

Clock

2 + SCY

1

Read

00

x

0

0

x

2  +  (2

 × 

SCY)

1

Read

10

x

(1 + 1/4)

 × 

Clock

0

x

3 + (2

 × 

SCY)

 

1

Read

11

x

(1 + 1/2)

 × 

Clock

0

x

3 + (2

 × 

SCY)

1

Write

00

0

0

0

0

2 + (2

 × 

SCY)

1

Write

10

0

(1 + 1/4)

 × 

Clock

0

0

3 + (2

 × 

SCY)

1

Write

11

0

(1 + 1/2)

 × 

Clock

0

0

3 + (2

 × 

SCY)

1

Write

00

1

0

0

–(1 + 1/4)

 × 

Clock

3 + (2

 × 

SCY)

1

Write

10

1

(1 + 1/4)

 × 

Clock

–(1 + 1/4) 

× 

Clock

–(1 + 1/4)

 × 

Clock

4 + (2

 × 

SCY)

1

Write

11

1

(1 + 1/2)

 × 

Clock

–(1 + 1/4) 

× 

Clock

–(1 + 1/4)

 × 

Clock

4 + (2

 × 

SCY)

SCY is the number of wait cycles from the option register.

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8113

EAW MX250 Owner'S Manual preview
MX250
Brand: EAW Pages: 10
XMG OASIS Disassembly Procedure preview
OASIS
Brand: XMG Pages: 5
NAD M10 Quick Setup Manual preview
M10
Brand: NAD Pages: 2
Mackie SP260 Installation Instructions preview
SP260
Brand: Mackie Pages: 2
Mackie SP260 Product Overview preview
SP260
Brand: Mackie Pages: 5
Tandberg Data RDX QuikStation 4 Quick Start Manuals preview
RDX QuikStation 4
Brand: Tandberg Data Pages: 2
Zoom B9.1ut Operation Manual preview
B9.1ut
Brand: Zoom Pages: 88
Grizzly PSJ-M3 GEN2 User Manual preview
PSJ-M3 GEN2
Brand: Grizzly Pages: 9
MF DIGITAL DIRECTOR PRO series Operator'S Manual preview
DIRECTOR PRO series
Brand: MF DIGITAL Pages: 79
Cervoz MEC-COM-2032i User Manual preview
MEC-COM-2032i
Brand: Cervoz Pages: 22
Nvidia Quadro M6000 Sync User Manual preview
Quadro M6000 Sync
Brand: Nvidia Pages: 8
Silicon Systems SiliconDrive SSD-P16G(I)-3100 Datasheet preview
SiliconDrive SSD-P16G(I)-3100
Brand: Silicon Systems Pages: 108
Supero SAS 846 TQ User Manual preview
SAS 846 TQ
Brand: Supero Pages: 16
MF DIGITAL 5200 Live Series EventCD Operator'S Manual preview
5200 Live Series EventCD
Brand: MF DIGITAL Pages: 21
ATI Technologies Radeon Online Manual preview
Radeon
Brand: ATI Technologies Pages: 87
AXIOMTEK UST510-52B-FL Series User Manual preview
UST510-52B-FL Series
Brand: AXIOMTEK Pages: 77
Renesas Emulation Memory Board R0E330850MSRC0 User Manual preview
Emulation Memory Board R0E330850MSRC0
Brand: Renesas Pages: 4
Renesas H8SX1664 User Manual preview
H8SX1664
Brand: Renesas Pages: 21

Brands by name

Popular brands

Load more brands