manualshive.com logo in svg

NXP Semiconductors MSC8113, Reference Manual

The NXP Semiconductors MSC8113 Reference Manual is an essential resource for users of this cutting-edge product. It provides in-depth guidance on its features, functionalities, and usage. Download the manual for free from our website to maximize your understanding and optimize your experience with the MSC8113.

Share
Download
background image

MSC8113 Reference Manual, Rev. 0

1-10

Freescale Semiconductor

MSC8113 Overview

Since the instructions can be shared, a typical application stores them in the shared memory, M2. 
Since each DSP core typically spends most of the time running loops of selected routines, these 
routines can be stored either in the local M1 memory or automatically fetched to the local cache. 
Achieving high hit ratios on the cache prevents core stalls and thus boosts overall performance. 
During a miss, instructions are fetched from the M2 memory through the MQBus. Since the miss 
ratio is very low, the probability of a collision with another SC140 core on the MQBus is low. 
Therefore, the overall fetch latency is low. Since different channels do not typically share data, 
the data can be located in the local M1 memory. The architecture is flexible enough to enable 
storage of data in M2 as well. In fact, the powerful DMA can perform data overlays between the 
M2 and the M1 memories or between the M1 memory of one SC140 core to the M1 memory of 
another SC140 core. For example, while performing channel N, the DMA controller can bring in 
the data needed for channel N+1. To achieve the best transfer rate, these DMA transfers can be 
programmed as flyby transfers, also called “single access transactions.” For a flyby transfer, the 
data path is between a peripheral and memory with the same port size, located on the same bus. 
Flyby transactions can occur only between external peripherals and external memories located on 
the system bus, between internal peripherals and internal SRAM located on the local bus, and 
between internal memories.

The SC140 core accesses the M2 memory through the MQBus. All accesses to other internal 
peripherals and accesses external to the MSC8113 occur on a separate bus, the SQBus. This 
separation ensures that the latencies for SC140 core accesses to the M2 memory remain as low as 
possible. Write accesses with high latencies are typically routed through the write buffer. The 
write buffer can store the write access, release the SC140 core, and execute it at a later time.

The SC140 cores should be focused on the intensive computational work and should not have to 
deal with bringing new data buffers. Data can be prepared in the M1 (or M2) memory in a “next” 
buffer while the SC140 core processes the ‘current’ buffer. The SC140 core can use the flexible 
DMA controller to transfer large blocks of data from the external memory to the internal memory 
and also between the internal memories. In some applications, data is written from an external 
host directly to the MSC8113 M1 and M2 memories through the DSI interface while the SC140 
handles the computational work in parallel. 

Note:

For details on the SC140 core, see Chapter 2, SC140 Core Overview.

1.2.1   Extended Core

The extended core contains the SC140 core, its M1 memory, an instruction cache, a write buffer, 
a programmable interrupt controller (PIC), a local interrupt controller (LIC) and interfaces to the 
MQBus and the SQBus through which accesses are performed to addresses outside the extended 
core. See Figure 1-2.

Note:

Details on extended core functionality are in Chapter 9, Extended Core.

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8113

VMIC VMICPCI-7755 Product Manual preview
VMICPCI-7755
Brand: VMIC Pages: 126
EMCIS LISN User'S Operating Manual preview
LISN
Brand: EMCIS Pages: 14
QNAP Turbo NAS TVS-71 Series Hardware User Manual preview
Turbo NAS TVS-71 Series
Brand: QNAP Pages: 51
Longshine LCS-8170 User Manual preview
LCS-8170
Brand: Longshine Pages: 35
Crystal Vision TANDEM HD-21 User Manual preview
TANDEM HD-21
Brand: Crystal Vision Pages: 54
ICP DAS USA iWSN-200E Quick Start Manual preview
iWSN-200E
Brand: ICP DAS USA Pages: 8
Penguin Edge MVME2500 Quick Start Manual preview
MVME2500
Brand: Penguin Edge Pages: 2
Abit G740A Installation Manual And User'S Manual preview
G740A
Brand: Abit Pages: 22
Hafele Suzie-Q 541.35.520 Mounting Instructions preview
Suzie-Q 541.35.520
Brand: Hafele Pages: 12
Ubiquiti airMAX NanoBridge M NBM3 Quick Start Manual preview
airMAX NanoBridge M NBM3
Brand: Ubiquiti Pages: 24
Tripp Lite SmartRack SR25UBEXP Specifications preview
SmartRack SR25UBEXP
Brand: Tripp Lite Pages: 4
Aaeon GENE-EHL7 User Manual preview
GENE-EHL7
Brand: Aaeon Pages: 119
Ricoh Network Scanning Unit A Operating Instructions Manual preview
Network Scanning Unit A
Brand: Ricoh Pages: 206
Idis DR-8364F Quick Manual preview
DR-8364F
Brand: Idis Pages: 16
Microchip Technology PD-9501-10GCO/AC User'S Installation Manual preview
PD-9501-10GCO/AC
Brand: Microchip Technology Pages: 41
Ceragon Fibe-Air IP-10G Installation Manual preview
Fibe-Air IP-10G
Brand: Ceragon Pages: 71
Enterasys GPIM-08 Reference Sheet preview
GPIM-08
Brand: Enterasys Pages: 2
ZALMAN CNPS10X Flex User Manual preview
CNPS10X Flex
Brand: ZALMAN Pages: 12

Brands by name

Popular brands

Load more brands