NXP Semiconductors MSC8113 Reference Manual Download Page 732 | Manualshive

Page: 732 / 1202

background image

MSC8113 Reference Manual, Rev. 0

22-8

Freescale Semiconductor

Timers

22.1 Timers Programming Model

All timer registers are mapped into the IPBus address space. Refer to Chapter 8, Memory Map.
The timer registers are divided into configuration, control, and status registers as follows:

Configuration registers. Configure the timer input and output forms, the timer operation
mode, and the compare values. Program each register before the timer is enabled and do
not change the values while the timer is enabled. There are both global configuration
registers and configuration registers for individual timers. Writing to configuration
registers is not allowed when the timers are enabled.

Control registers. Enable the timers and the interrupts. These registers can be changed
during timer operation. There are both global control registers and control registers for
individual timers.

Status registers. Can be accessed at any time.

Note:

The global configuration and control registers configure all 16 timers in a module,
including the registers that define the I/O.

This section describes the timer module registers, which are listed as follows:

Timer General Configuration Register A (TGCRA), page 22-9

Timer General Configuration Register B (TGCRB), page 22-10

Timer Interrupt Enable Register A (TIERA), page 22-11

Timer Interrupt Enable Register B (TIERB), page 22-11

Timer Configuration Register A (TCFRA[0–15]), page 22-12

Timer Configuration Register B (TCFRB[0–15]), page 22-14

Timer Compare Register A (TCMPA[0–15]), page 22-15

Timer Compare Register B (TCMPB[0–15]), page 22-15

Timer Control Register A (TCRA[0–15]), page 22-16

Timer Control Register B (TCRB[0–15]), page 22-16

Timer Status Register A (TSRA), page 22-17

Timer Status Register B(TSRB), page 22-17

Timer Event Register A (TERA), page 22-18

Timer Event Register B (TERB), page 22-18

Timer Count Register A (TCNRA[0–15]), page 22-19

Timer Count Register B (TCNRB[0–15]), page 22-20

«
...
730
731
732
733
734
...
»

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8113

Brand: LAWO Pages: 154

Brand: Lab.gruppen Pages: 35

Brand: XESS Pages: 23

Brand: GAMDIAS Pages: 15

RUGGEDMAX WIN7000

Brand: RuggedCom Pages: 42

Brand: T.A Pages: 11

Brand: Grundig Pages: 24

Brand: Rolls Pages: 1

Brand: PairGain Pages: 80

Brand: Rockwell Automation Pages: 21

FiberTwist XGS2410

Brand: Genexis Pages: 7

Brand: EVGA Pages: 3

FiberTwist XGS2420

Brand: Genexis Pages: 7

Brand: SilverStone Pages: 16

Brand: Vxl Pages: 4

Brand: LanReady Pages: 40

Brand: ICS Advent Pages: 30

IE-703089-MC-EM1

Brand: NEC Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands