manualshive.com logo in svg

NXP Semiconductors MSC8113, Reference Manual

The NXP Semiconductors MSC8113 Reference Manual is an essential resource for users of this cutting-edge product. It provides in-depth guidance on its features, functionalities, and usage. Download the manual for free from our website to maximize your understanding and optimize your experience with the MSC8113.

Share
Download
background image

MSC8113 Reference Manual, Rev. 0

9-16

Freescale Semiconductor

Extended Core

For example, an area with base address = 1MB; size = 256 KB supports the basic condition that 
the base be an integer multiple of the size. The steps in defining this are as follows:

1.

Write the base address in 32-bit representation. The 1 MB is written as 
00000000000100000000000000000000.

2.

According to the size (256 KB), choose line 11 in Table 9-4. The size_bit = 0.

3.

Determine the base bits for the DBR. The 10 lowest bits are determined according to 
Table 9-4 as 1000000000. The upper bits are determined according to the remaining 
bits ([31–18]) of the base address, which means 00000000000100.

4.

This results in: base = 0x001200, or in binary form 000000000001001000000000. The 8 
non-written lsb = 0x00.

After the area is sized, the global and IMM bits determine whether this area is global, immediate, 
or immediate with no freeze. The area can be global and immediate at the same time. The area 
can be reversed, so it does not have the value it was set to. For example, if the immediate bit is set 
and the reverse bit is set, this area is not immediate. A reverse area has a higher priority, so a 
reverse area can be set inside an area. Figure 9-8 shows a reverse area inside an area in the 
memory space. Register 0 determines an area in memory, and register 1 determines a reverse area 
inside the register 0 area. If the immediate bit is set in both registers, the data area 0 without the 
data area 1 is the immediate area.

Figure 9-8.  Reverse Area Inside an Area

Base 0 Area

Size 0 Area

Data Area 0

Size 1 Area

Base 1 Area

Data Area 1 (reverse)

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8113

ForeScout CounterACT Quick Installation Manual preview
CounterACT
Brand: ForeScout Pages: 28
FOR-A USF-105AS Operation Manual preview
USF-105AS
Brand: FOR-A Pages: 39
Zhone IMACS Network Device Product Manual preview
IMACS Network Device
Brand: Zhone Pages: 114
ZyXEL Communications ZyXEL ZyAIR B-120 Quick Installation Manual preview
ZyXEL ZyAIR B-120
Brand: ZyXEL Communications Pages: 20
WAGO 750-459 Manual preview
750-459
Brand: WAGO Pages: 48
Kaptia Klever Getting Started preview
Klever
Brand: Kaptia Pages: 14
Acromag APCe7012E-LF User Manual preview
APCe7012E-LF
Brand: Acromag Pages: 23
Top RAMS1000 User Manual preview
RAMS1000
Brand: Top Pages: 21
Supermicro X12SPO-NTF/-F User Manual preview
X12SPO-NTF/-F
Brand: Supermicro Pages: 131
Stahl HFisolator 9730/26-11 Operating Instructions preview
HFisolator 9730/26-11
Brand: Stahl Pages: 2
EZCast Pro Dongle II D10 Repair Manual preview
Dongle II D10
Brand: EZCast Pro Pages: 4
ekwb EK-FC R9-295X2 Installation And Mounting Manual preview
EK-FC R9-295X2
Brand: ekwb Pages: 2
Navitar 1-62643 Dimensional Drawing preview
1-62643
Brand: Navitar Pages: 1
DIGITAL-LOGIC MICROSPACE MSEBX800 User Manual preview
MICROSPACE MSEBX800
Brand: DIGITAL-LOGIC Pages: 53
Thermalright Macho Rev. A (BW) Manual preview
Macho Rev. A (BW)
Brand: Thermalright Pages: 32
Harman Lexicon MPX 200 User Manual preview
Lexicon MPX 200
Brand: Harman Pages: 77
Nexus OSL101 Instructions Manual preview
OSL101
Brand: Nexus Pages: 9
ASTRO U 960 Operating Manual preview
U 960
Brand: ASTRO Pages: 12

Brands by name

Popular brands

Load more brands