manualshive.com logo in svg

NXP Semiconductors MSC8113, Reference Manual

The NXP Semiconductors MSC8113 Reference Manual is an essential resource for users of this cutting-edge product. It provides in-depth guidance on its features, functionalities, and usage. Download the manual for free from our website to maximize your understanding and optimize your experience with the MSC8113.

Share
Download
background image

Architecture

MSC8113 Reference Manual, Rev. 0

Freescale Semiconductor

1-21

„

Local bus. A 64-bit wide bus connecting the Ethernet Controller, TDM, DSI, DMA 
controller, and the local-to-system bus bridge to each other. The extended cores also share 
this bus, which connects to the M1 memory of each SC140 core. This multi-master 
multi-slave bus runs at 166 MHz. The DSI, TDM, DMA controller, and the bridge are the 
masters of this bus. The internal memories are slaves to this bus, which is primarily used 
for transferring data between the chip interfaces to the internal memories. 

„

System bus. A 64-bit wide bus controlled by the SIU that connects the DMA controller and 
system interface (from the SQBus) through the SIU memory controller to the external 
32/64 bit system bus. It also connects to the local-to-system bus bridge to allow data 
transfers between the 60x-compatible local and internal system buses.

— 64/32-bit data and 32-bit address bus.
— Support for multiple-master designs.
— Four-beat burst transfers (eight-beat in 32-bit wide mode).
— Port size of 64, 32, 16, and 8 controlled by the internal memory controller.
— Bus accesses external memory or peripherals, or an external host device uses it to 

access internal resources.

— Slave support, direct access by an external host to internal resources including the M1 

and M2 memories.

— Internal arbitration between up to four master devices.

„

The external buses can be configured during reset in three modes:

— 64-bit data DSI and 32-bit data system bus.
— 32-bit data DSI and 64-bit data system bus.
— 32-bit data DSI, 32 bit data system, and Ethernet MII or RMII.

1.2.8   TDM Serial Interface

The TDM interface connects gluelessly to common telecommunication framing schemes, such as 
T1 and E1 lines. It can also connect to multiple framers and switches, as well as to commons 
buses such as the ST-BUS. The TDM contains four identical and independent engines. Each 
TDM engine can be configured in one of the following options:

„

Two independent receive and transmit links. 

— The transmit has an input clock of up to 50 MHz, output data, and a frame sync that is 

configured as either input or output. Up to 256 transmit channels are supported.

— The receive has an input clock of up to 50 MHz, input data, and an input frame sync. 

Up to 256 receive channels are supported.

„

Two receive and two transmit links share the clock and the frame sync. The input clock 
runs up to 25 MHz, and the sync is configured as either input or output. Each of the two 
receive links supports up to 128 channels, and each transmit link supports up to 128 
channels.

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8113

3Com 486 Getting Started Manual preview
486
Brand: 3Com Pages: 20
XMG OASIS Disassembly Procedure preview
OASIS
Brand: XMG Pages: 5
NAD M10 Quick Setup Manual preview
M10
Brand: NAD Pages: 2
Eaton INDGW-X2 Manual preview
INDGW-X2
Brand: Eaton Pages: 10
Pima ZEL508 Installation Instructions preview
ZEL508
Brand: Pima Pages: 4
East Coast Datacom PDS-1/10G User Manual preview
PDS-1/10G
Brand: East Coast Datacom Pages: 19
RANA Systems RanaSystems 13-0010--001 User Manual preview
RanaSystems 13-0010--001
Brand: RANA Systems Pages: 328
SYNTEK STA-UI-A0035 User Manual preview
STA-UI-A0035
Brand: SYNTEK Pages: 41
AMX AXB-PSCV Dimensional Drawing preview
AXB-PSCV
Brand: AMX Pages: 1
Bridgeworks Tamar FCSAS102800 User Manual preview
Tamar FCSAS102800
Brand: Bridgeworks Pages: 56
7th Sense Pixel Processing Juggler User Manual preview
Pixel Processing Juggler
Brand: 7th Sense Pages: 148
Data Translation DT9835 Getting Started Manual preview
DT9835
Brand: Data Translation Pages: 62
PairGain T1L2F10A Manual preview
T1L2F10A
Brand: PairGain Pages: 76
Jennic JN5148 Reference Manual preview
JN5148
Brand: Jennic Pages: 14
Cabletron Systems TRMIM-10R Installation Manual preview
TRMIM-10R
Brand: Cabletron Systems Pages: 54
Hitachi DS120 G2 Hardware Manual preview
DS120 G2
Brand: Hitachi Pages: 17
Hitachi LQE050 Hardware Manual preview
LQE050
Brand: Hitachi Pages: 53
Hitachi G-SPEED ES PRO Installation Manual preview
G-SPEED ES PRO
Brand: Hitachi Pages: 23

Brands by name

Popular brands

Load more brands