manualshive.com logo in svg

NXP Semiconductors MSC8113, Reference Manual

The NXP Semiconductors MSC8113 Reference Manual is an essential resource for users of this cutting-edge product. It provides in-depth guidance on its features, functionalities, and usage. Download the manual for free from our website to maximize your understanding and optimize your experience with the MSC8113.

Share
Download
background image

Architecture

MSC8113 Reference Manual, Rev. 0

Freescale Semiconductor

17-11

„

Interrupt Group B has the following interrupt sources:

— Eight dedicated timers, with different timers for each SC140.
— Eight DMA channel interrupts, half of the channels connected to the LICs of SC140s 0 

and 1, half to the LICs of SC140s 2 and 3.

— One global UART interrupt.
— Two global SIU interrupts from PIT and TMCNT.
— Five global 

IRQ

s.

— Eight virtual system interrupts from the GIC (see Section 17.1.1.3, Virtual Interrupt 

Generation, on page 17-7).

— Typically, the interrupt mapping is divided into one for DMA, one for SIU interrupts, 

one for timers, and one for virtual interrupts, but any other combination is valid, 
depending on the application.

Each interrupt source has the following programmable attributes:

„

Two bits of IMAP control field map it to one of four interrupt output lines to the PIC.

„

Two bits of EM (Edge Mode) select the interrupt source handling as level, edge, or dual 
edge mode.

„

A primary status bit.

„

In dual edge mode, a second edge error status bit. The sum of all second edge error status 
bits is sampled to generate a single second edge error detection interrupt output line to the 
PIC.

For details on LIC interrupts received at the PIC, see Table 17-8.

17.1.2.1   Resolving LIC Interrupts by the SC140 Cores

The SC140 cores support counting of leading bits using the CLB instruction. This feature can be 
used to achieve fast priority resolution between interrupts having the same priority level (that is, 
mapped to the same PIC input). The primary priority level is separated by mapping an interrupt 
source to different PIC inputs. Following is a simple SC140 core algorithm that uses both the PIC 
vector system and the CLB instruction for rapid detection of the LIC interrupt source to be 
serviced and for prioritizing the bit by location:

„

Interrupts with different primary priority levels are mapped to different PIC inputs. Each 
group connects to four PIC inputs, and both groups share one PIC input for second edge 
error interrupts.

„

While mapping and enabling a specific LIC interrupt source to a PIC input, the application 
should also set the appropriate bit in the 32-bit mask value associated with that input. Each 
bit set in this mask indicates that the specific LIC interrupt source is mapped to this PIC 
input. At the end of this set up, each PIC-mappable input from the LIC has an associated 
updated 32-bit mask value.

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8113

3xLogic V250 Quick Start Manual preview
V250
Brand: 3xLogic Pages: 2
National Instruments FieldPoint cFP-RTD-122 Operating Instructions Manual preview
FieldPoint cFP-RTD-122
Brand: National Instruments Pages: 15
D3 DesignCore RVP-TDA3 Series Quick Start Manual preview
DesignCore RVP-TDA3 Series
Brand: D3 Pages: 34
FONESTAR XO-324 Instruction Manual preview
XO-324
Brand: FONESTAR Pages: 8
AOpen VA1000 Lite2 User Manual And Technical Manual preview
VA1000 Lite2
Brand: AOpen Pages: 18
ebm-papst W3G710-NK67-01 Operating Instructions Manual preview
W3G710-NK67-01
Brand: ebm-papst Pages: 13
ZALMAN CNPS5X PERFORMA User Manual preview
CNPS5X PERFORMA
Brand: ZALMAN Pages: 8
Symantec SV1800 Series Safety And Regulatory Compliance Manual preview
SV1800 Series
Brand: Symantec Pages: 100
ZiLOG Z8 GP ZGP323 User Manual preview
Z8 GP ZGP323
Brand: ZiLOG Pages: 11
Echo LAYLA 3G Owner'S Manual preview
LAYLA 3G
Brand: Echo Pages: 21
Digital Audio Corporation PCAP II User Manual preview
PCAP II
Brand: Digital Audio Corporation Pages: 164
XtendLan XL-VC102SB User Manual preview
XL-VC102SB
Brand: XtendLan Pages: 17
Quatech SSPX-100 User Manual preview
SSPX-100
Brand: Quatech Pages: 5
Xilinx DPU IP Product Manual preview
DPU IP
Brand: Xilinx Pages: 43
Extreme Networks ACC-BKT-AX-BEAM Accessories Manual preview
ACC-BKT-AX-BEAM
Brand: Extreme Networks Pages: 35
AXIOMTEK IPC934-230-FL Quick Installation Manual preview
IPC934-230-FL
Brand: AXIOMTEK Pages: 2
Commax CVN-0430F User Manual preview
CVN-0430F
Brand: Commax Pages: 122
ST STEVAL-IHT003V1 User Manual preview
STEVAL-IHT003V1
Brand: ST Pages: 20

Brands by name

Popular brands

Load more brands