NXP Semiconductors MSC8113 Reference Manual Download Page 858 | Manualshive

Page: 858 / 1202

background image

MSC8113 Reference Manual, Rev. 0

25-88

Freescale Semiconductor

Ethernet Controller

Table 25-61. HAFDUPR Bit Descriptions

Bit

Reset

Description

Settings

—

0–7

0

Reserved. Write to zero for future compatibility.

ABEBT

8–11

0101

Alternate Binary Exponential Back-off Truncation
In use while ABEB is set. The value programmed is substituted
for the Ethernet standard value of ten. The default is 0xA.

ABEB

12

0

Alternate Binary Exponential Back-off Enable
Configures the Tx MAC to use the alternate binary exponential
back-off truncation (ABEBT) setting instead of the 802.3
standard tenth collision. The standard specifies that any
collision after the tenth uses one less than 210 as the
maximum back-off time.

0

Tx MAC follows the binary
exponential back-off rule.

1

Tx MAC uses alternate binary
exponential back-off rule.

BPNB

13

0

Back Pressure No Back-off
Configures the Tx MAC to retransmit the data immediately
after a collision, during a back pressure operation.

0

Tx MAC follows the binary
exponential back-off rule.

1

No back-off during a back
pressure operation.

NB

14

0

No Back-off
Configures the Tx MAC to immediately re-transmit following a
collision.

0

Tx MAC follows the binary
exponential back-off rule.

1

No back-off.

ED

15

1

Excess Defer
Configures the Tx MAC to allow the transmission of a packet
that is excessively deferred.

0

Abort an excessively deferred
packet.

1

Transmit an excessively
deferred packet.

RTXM
16–19

1111

Retransmission Maximum
This programmable field specifies the number of
retransmission attempts following a collision before the packet
is aborted due to excessive collisions. The standard specifies
the attempt limit to be 0xF (15d).

—

20–25

0

Reserved. Write to zero for future compatibility.

CW

26–31

110111

Collision Window
This programmable field represents the slot time or collision
window during which collisions occur in properly configured
networks. Because the collision window starts at the beginning
of transmission, the preamble and SFD are included. Its
default of 0x37 (55d) corresponds to the count of frame bytes
at the end of the window.

«
...
856
857
858
859
860
...
»

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8113

C50FSi - VB Network Camera

Brand: Canon Pages: 32

Brand: Rabbit Pages: 120

Brand: Data Translation Pages: 60

Brand: dbx Pages: 2

Brand: dbx Pages: 17

Brand: FabiaTech Pages: 4

DR-4100P Series

Brand: Idis Pages: 30

Brand: Idis Pages: 31

Brand: Direct IP Pages: 76

PG-FlexPlus AMU-912

Brand: ADC Pages: 130

Brand: Fieldbus Specialists Pages: 39

DesignCore RVP-TDA3 Series

Brand: D3 Pages: 34

Brand: protech Pages: 95

Optane Persistent Memory 200 Series

Brand: Supermicro Pages: 54

Brand: XJTAG Pages: 9

Brand: Xilinx Pages: 8

Brand: S&T Pages: 28

PFC Chokes PFC3515V Series

Brand: Delta Electronics Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands