manualshive.com logo in svg

NXP Semiconductors MSC8113, Reference Manual

The NXP Semiconductors MSC8113 Reference Manual is an essential resource for users of this cutting-edge product. It provides in-depth guidance on its features, functionalities, and usage. Download the manual for free from our website to maximize your understanding and optimize your experience with the MSC8113.

Share
Download
background image

MSC8113 Reference Manual, Rev. 0

12-38

Freescale Semiconductor

Memory Controller

When ORx[TRLX] and ORx[CSNT] are set in a write-memory access, the strobe lines, 

PWE[0–7]

 

are deasserted one clock earlier than in the normal case. If ORx[ACS]

 ≠ 

00, 

CS

 is also deasserted 

one clock earlier, as shown in Figure 12-38 and Figure 12-39. When a bank is selected to 
operate with external transfer acknowledge (ORx[SETA] = 1 and ORx[TRLX] = 1), the memory 
controller does not support external devices that provide 

PSDVAL

 to complete the transfer with 

zero wait states. The minimum access duration in this case is three clock cycles.

12.3.1.4   Output Enable (POE) Timing 

The timing of the 

POE

 is affected only by TRLX. It always asserts and deasserts on the rising 

edge of the external bus clock. 

POE

 always asserts on the rising clock edge after 

CS

 is asserted, 

and therefore its assertion can be delayed (along with the assertion of 

CS

) by programming 

ORx[TRLX] = 1. 

POE

 deasserts on the rising clock edge coinciding with or immediately after 

CS

 

deassertion. 

12.3.1.5   Programmable Wait State Configuration

The GPCM supports internal 

PSDVAL

 generation. It allows fast accesses to external memory 

through an internal 60x-compatible bus master or a maximum 17-clock access by programming 
ORx[SCY]. The internal 

PSDVAL

 generation mode is enabled if ORx[SETA] = 0. If 

PGTA

 is 

asserted externally at least two clock cycles before the wait state counter expires, the current 
memory cycle is terminated. When ORx[TRLX] = 1, the number of wait states inserted by the 
memory controller is defined by 2 

×

 SCY or a maximum of 30 wait states.

Figure 12-37.  GPCM Relaxed-Timing Write (ACS = 1x, SCY = 0, CSNT = 0,TRLX = 1)

Clock

Address

PSDVAL

CSx

BCTL0

PWE

POE

Data

ACS = 10

ACS = 11

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8113

D-Link ShareCenter Pulse DNS-320 Quick Install Manual preview
ShareCenter Pulse DNS-320
Brand: D-Link Pages: 2
D-Link DFE-680TX Quick Install Manual preview
DFE-680TX
Brand: D-Link Pages: 4
M-Audio Computer Quick Start Manual preview
Computer
Brand: M-Audio Pages: 10
Samsung NAS Series Hardware User Manual preview
NAS Series
Brand: Samsung Pages: 65
NXP Semiconductors MIMXRT1160 Hardware Development Manual preview
MIMXRT1160
Brand: NXP Semiconductors Pages: 24
AMD SB710 User Manual preview
SB710
Brand: AMD Pages: 20
Keil RTX51 Manual preview
RTX51
Brand: Keil Pages: 68
hilscher netHOST NHST-T100 User Manua preview
netHOST NHST-T100
Brand: hilscher Pages: 75
ADLINK Technology MCM-216 User Manual preview
MCM-216
Brand: ADLINK Technology Pages: 69
Enterasys Matrix 6H303-48 Hardware Installation Manual preview
Matrix 6H303-48
Brand: Enterasys Pages: 90
C-Data FD612H User Manual preview
FD612H
Brand: C-Data Pages: 19
ebm-papst 8314/2H Operating Manual preview
8314/2H
Brand: ebm-papst Pages: 6
ebm-papst D3G160-BD05-02 Operating Instructions Manual preview
D3G160-BD05-02
Brand: ebm-papst Pages: 12
HeimVision HM243 User Manual preview
HM243
Brand: HeimVision Pages: 167
Extron electronics EDID 101D User Manual preview
EDID 101D
Brand: Extron electronics Pages: 20
Extron electronics IPL Pro Series User Manual preview
IPL Pro Series
Brand: Extron electronics Pages: 10
HP ProCurve Radio Port 210 Installation And Getting Started Manual preview
ProCurve Radio Port 210
Brand: HP Pages: 36
HP StorageWorks T5521A Specifications preview
StorageWorks T5521A
Brand: HP Pages: 20

Brands by name

Popular brands

Load more brands