NXP Semiconductors MSC8113 Reference Manual Download Page 364 | Manualshive

Page: 364 / 1202

background image

MSC8113 Reference Manual, Rev. 0

12-56

Freescale Semiconductor

Memory Controller

Additional information on some of the RAM word fields is as follows:

Chip-Select Signals (

CxTx

). If BRx[MS] of the accessed bank selects a UPM on the

currently requested cycle, the UPM manipulates the

CS

signal for that bank with timing as

specified in the UPM RAM word. The selected UPM affects only assertion and
deassertion of the appropriate

CS

signal. The state of the selected

CSx

signal of the

corresponding bank depends on the value of each CSTx bit. Figure 12-52 and the timing
diagrams in Figure 12-50 show how UPMs control

CS

signals.

Byte-Select Signals (

BxTx

). If BRx[MS] of the accessed memory bank selects a UPM on

the currently requested cycle, the selected UPM affects only the assertion and deassertion
of the appropriate

BS

signals; their timing is specified in the RAM word. The

BS

signals

are controlled by the port size of the accessed bank, the transfer size of the transaction, and
the address accessed. Figure 12-53 shows how UPMs control

BS

signals. Table 12-22

shows how

BS

signals affect 64-, 32-, 16-, and 8-bit accesses. Note that for a refresh timer

request, the UPM asserts/deasserts all the

BS

signals. The uppermost byte-select (

BS[0]

)

indicates that

D[0–7]

contains valid data during a cycle. Similarly,

BS[[1]

indicates that

D[8–15]

contains valid data,

BS[2]

indicates that

D[16–23]

contains valid data, and

BS[3]

indicates that

D[24–31]

contains valid data during a cycle, and so forth.

Figure 12-52. CS Signal Selection

UPMA/B/C

SDRAM

GPCM

MUX

CS3
CS4
CS5
CS6
CS7

Switch

Bank Selected

CS11

CS0
CS1
CS2

CS9 do not use

BRx[MS]

CS9

UPM (use GPCM for
IPBus Peripherals)

CS11 uses UPM

for internal memories

In MSC8113:

«
...
362
363
364
365
366
...
»

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8113

Brand: ETAS Pages: 69

Brand: STONEFLY Pages: 48

Brand: BSS Audio Pages: 20

Brand: Reeven Pages: 2

PG-FlexPlus AMU-912

Brand: ADC Pages: 130

Brand: Fieldbus Specialists Pages: 39

Brand: NA Pages: 22

F-Tile SDI II Intel Agilex

Brand: Intel Pages: 39

Oresund EFC102200

Brand: Bridgeworks Pages: 84

iCE40 SPRAM Series

Brand: Lattice Semiconductor Pages: 12

Brand: Rajant Corporation Pages: 40

UniFi WiFi BaseStation XG

Brand: Ubiquiti Pages: 19

Emotron OSTO 100

Brand: CG Pages: 112

Brand: Z-Wave Pages: 42

Brand: National Instruments Pages: 121

AirBridge VS-YOFIMN-000

Brand: Vivint Pages: 2

Brand: ADLINK Technology Pages: 95

Brand: MEN Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands