manualshive.com logo in svg

NXP Semiconductors MSC8113, Reference Manual

The NXP Semiconductors MSC8113 Reference Manual is an essential resource for users of this cutting-edge product. It provides in-depth guidance on its features, functionalities, and usage. Download the manual for free from our website to maximize your understanding and optimize your experience with the MSC8113.

Share
Download
background image

MSC8113 Reference Manual, Rev. 0

12-44

Freescale Semiconductor

Memory Controller

12.3.3   Boot Chip-Select Operation

Boot chip-select operation allows address decoding for a boot ROM before system initialization. 
The 

CS0

 signal is the boot chip-select output; its operation differs from the other external 

chip-select outputs on system reset. When the MSC8113 internal core begins accessing memory 
at system reset, 

CS0

 is asserted for every address in the boot address range, unless an internal 

register is accessed. The address range is configured during reset. The boot chip-select also 
provides a programmable port size during system reset by using the configuration mechanism 
described in Section 5.2, Reset Configuration. The boot chip-select does not provide write 
protection. 

CS0

 operates this way until the first write to OR0, and it can be used as any other 

chip-select register once the preferred address range is loaded into BR0. After the first write to 
OR0, the boot chip-select can be restarted only on hardware reset. Table 12-18 describes the 
initial values of the boot bank in the memory controller.

12.3.4   Differences Between MPC8xx GPCM and MSC8113 GPCM

If you are familiar with the MPC8xx GPCM, you should know about the following differences 
between the MPC8xx GPCM and the MSC8113 GPCM:

„

External termination. In the MPC8xx the external termination connects to the external 
system bus 

TA

 signal and so must be asserted in sync with the system clock. In the 

MSC8113, this signal is separated from the bus and named 

PGTA

. The signal is 

synchronized internally and sampled. The sampled signal is used to generate 

TA

, which 

terminates the bus transaction.

„

Extended hold time. Extended hold time for reads can be up to eight clock cycles (instead 
of one in the MPC8xx).

Table 12-18.  Boot Bank Field Values After Reset  

Register

Settings

BR0

BA[0–16]
PS [0–1]
DECC[0–1]
WP
MS[0–2]
EMEMC
ATOM[0–1]
DR
V

11111110000000000
From HRCW. See Section 5.6.1, Hard Reset Configuration Word.
00
0
000
From HRCW.
00
0
1

OR0

AM[0–16]
BCTLD
CSNT
ACS[0–1]
SCY[0–3]
SETA
TRLX
EHTR

11111110000000000 (32 MB)
0
1
11
1111
0
1
0

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8113

Z3 Technology Z3-DM8168-PCI-RPS Manual preview
Z3-DM8168-PCI-RPS
Brand: Z3 Technology Pages: 20
Z3 Technology Z3-DM8107-SDI2-RPS User Manual preview
Z3-DM8107-SDI2-RPS
Brand: Z3 Technology Pages: 75
Z-Wave USB Dongle User Manual preview
USB Dongle
Brand: Z-Wave Pages: 13
FOR-A USF-105AS Operation Manual preview
USF-105AS
Brand: FOR-A Pages: 39
Ubiquiti PowerBeam AC Gen2 Quick Start Manual preview
PowerBeam AC Gen2
Brand: Ubiquiti Pages: 22
8e6 Technologies ER3-100 (5K02-55) Quick Start Manual preview
ER3-100 (5K02-55)
Brand: 8e6 Technologies Pages: 74
ZALMAN ZM-2HC2 User Manual preview
ZM-2HC2
Brand: ZALMAN Pages: 8
Rajant Corporation BreadCrumb CX1 User Manual preview
BreadCrumb CX1
Brand: Rajant Corporation Pages: 40
AMX AXB-PSCV Dimensional Drawing preview
AXB-PSCV
Brand: AMX Pages: 1
NCR 7702-K134 Upgrade Manual preview
7702-K134
Brand: NCR Pages: 15
Waveshare High-Precision AD/DA Board User Manual preview
High-Precision AD/DA Board
Brand: Waveshare Pages: 8
ETAS ES1337.2 User Manual preview
ES1337.2
Brand: ETAS Pages: 29
Goobay 97790 User Manual preview
97790
Brand: Goobay Pages: 28
Datavideo NVW-150 Instruction Manual preview
NVW-150
Brand: Datavideo Pages: 71
EDT PCIe Gen1 Framegrabbers User Manual preview
PCIe Gen1 Framegrabbers
Brand: EDT Pages: 43
U-Media WST-375L User Manual preview
WST-375L
Brand: U-Media Pages: 42
Advantage Boost Box Setup Manual preview
Boost Box
Brand: Advantage Pages: 4
Advantech AIMB-788 User Manual preview
AIMB-788
Brand: Advantech Pages: 114

Brands by name

Popular brands

Load more brands