NXP Semiconductors MSC8113 Reference Manual Download Page 60 | Manualshive

Page: 60 / 1202

background image

MSC8113 Reference Manual, Rev. 0

2-4

Freescale Semiconductor

SC140 Core Overview

Figure 2-2 shows the architecture of the Data ALU.

With the ability to execute any two

MOVE

instructions in parallel every clock cycle, a maximum

data throughput of 6.4 GBps (at 400 MHz) can be achieved between the memory and the register
file.

2.1.1.1 Data Registers

The Data ALU registers are read or written over the data buses (XDBA and XDBB). The source
operands for Data ALU arithmetic instructions always originate from Data ALU registers. All the
Data ALU operations are performed in one clock cycle so that a new instruction can be initiated
in every clock, yielding a rate of up to four Data ALU instructions per clock cycle. The
destination of every arithmetic operation can be used as a source operand for the operation
immediately following, without any time penalty.

2.1.1.2 Multiply-Accumulate (MAC) Unit

The MAC unit comprises the main arithmetic processing unit of each SC140 core and performs
all the calculations on data operands. The MAC unit outputs one 40-bit result in the form of
[Extension:Most Significant Portion:Least Significant Portion] (EXT:MSP:LSP). The multiplier
executes 16-bit

×

16-bit fractional or integer multiplication between two’s complement signed,

unsigned, or mixed operands. The 32-bit product is right-justified and added to the 40-bit
contents of one of the sixteen data registers.

Figure 2-2. Data ALU Architecture

Memory Data Bus 1 (XDBA)

Memory Data Bus 2 (XDBB)

64

64

64

64

Shifter/Limiter

Data Registers D[0–15]

40

40

40

40

40

40

40

40

40

40

40

ALU

40

40

40

40

40

40

40

40

40

ALU

ALU

ALU

«
...
58
59
60
61
62
...
»

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8113

Brand: Tripp Lite Pages: 20

Brand: Lancom Pages: 70

Brand: Wintech Pages: 21

Brand: Datasat Pages: 24

Brand: Supersonic Pages: 46

Brand: Caen Pages: 14

Brand: SeaLevel Pages: 34

Brand: IFM Electronic Pages: 14

UniFi WiFi BaseStation XG

Brand: Ubiquiti Pages: 19

Emotron OSTO 100

Brand: CG Pages: 112

Brand: MFJ Pages: 11

Brand: Unex Pages: 27

Brand: Quadram Pages: 21

Brand: Cypress Semiconductor Pages: 31

High-Precision AD/DA Board

Brand: Waveshare Pages: 8

Brand: ETAS Pages: 29

AirBridge VS-YOFIMN-000

Brand: Vivint Pages: 2

DUAL Nx56/64 1200142L1#

Brand: ADTRAN Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands