manualshive.com logo in svg

NXP Semiconductors MSC8113, Reference Manual

The NXP Semiconductors MSC8113 Reference Manual is an essential resource for users of this cutting-edge product. It provides in-depth guidance on its features, functionalities, and usage. Download the manual for free from our website to maximize your understanding and optimize your experience with the MSC8113.

Share
Download
background image

MSC8113 Reference Manual, Rev. 0

18-2

Freescale Semiconductor

Debugging

18.1 Overview

The MSC8113 TAP consists of five dedicated signal lines, a 16-state TAP controller, and three 
test data registers. A Boundary Scan Register (BSR) links most of the device signal connections 
into a single shift register. The test logic, which uses static logic design, is independent of the 
device system logic. The MSC8113 JTAG can do the following:

„

Perform boundary scan operations to check circuit-board electrical continuity.

„

Bypass the MSC8113 for a given circuit-board test by effectively reducing the Boundary 
Scan Register (BSR) to a single cell.

„

Sample the MSC8113 system connections during operation and transparently shift out the 
result in the BSR. Preload values to outputs prior to circuit board testing.

„

Disable the drive to outputs during circuit board testing.

„

Access the EOnCE controller and circuits to control a target system.

„

Give entry to Debug mode.

„

Query identification information (manufacturer, part number and version) from an 
MSC8113-based device.

„

Force test data onto the outputs of an MSC8113-based device while replacing its BSR in 
the serial data path with a single-bit register.

Note:

Precautions must be taken to ensure that the IEEE Std. 1149.1-like test logic does not 
interfere with non-test operation. 

To access the JTAG registers, shift the appropriate command into the JTAG instruction register 
and then shift the required value into the register. See Section 18.3 for a discussion of the JTAG 
instructions. Figure 18-1 shows the MSC8113 JTAG 5-bit instruction register and the following 
test registers: 

„

Boundary Scan Register (BSR). Regarding the length of the BSR, The boundary scan bit 
definitions vary according to the specific chip implementation of the MSC8113 and are 
described by the BSDL file on the product website

„

1-bit Bypass Register

„

32-bit Identification Register (ID)

„

32-bit General Purpose Register (GPR) 

„

32-bit Parallel Input Register (PIREG)

Table 18-1 lists the test access port (TAP) signals.

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8113

Aaeon UP Squared 6000 Edge Computing Kit User Manual preview
UP Squared 6000 Edge Computing Kit
Brand: Aaeon Pages: 59
RadiSys EPC-31 Hardware Reference Manual preview
EPC-31
Brand: RadiSys Pages: 44
Garland INT10G10SP2 User Manual preview
INT10G10SP2
Brand: Garland Pages: 6
Renesas Compact Emulator M30620T-CPE User Manual preview
Compact Emulator M30620T-CPE
Brand: Renesas Pages: 52
Omega OMB-DAQBOARD-3000 Series User Manual preview
OMB-DAQBOARD-3000 Series
Brand: Omega Pages: 108
Altera DE2-70 User Manual preview
DE2-70
Brand: Altera Pages: 93
ADTRAN NetVanta 6355 PoE Installation Manual preview
NetVanta 6355 PoE
Brand: ADTRAN Pages: 46
IEI Technology PUZZLE-IN003B User Manual preview
PUZZLE-IN003B
Brand: IEI Technology Pages: 86
Dahua Technology Lite N42B1P Series Quick Start Manual preview
Lite N42B1P Series
Brand: Dahua Technology Pages: 14
Kontron 50099 067 User Manual preview
50099 067
Brand: Kontron Pages: 42
Valcom VIP-822A Quick Start Manual preview
VIP-822A
Brand: Valcom Pages: 4
Supero SAS 846 TQ User Manual preview
SAS 846 TQ
Brand: Supero Pages: 16
Isee IGEPv2 BOARD Hardware Reference Manual preview
IGEPv2 BOARD
Brand: Isee Pages: 68
Comway 4G DTU Configuration Instructions preview
4G DTU
Brand: Comway Pages: 20
Intel E5345 - Xeon 2.33 GHz 8M L2 Cache 1333MHz FSB LGA771 Active Quad-Core Processor Datasheet preview
E5345 - Xeon 2.33 GHz 8M L2 Cache 1333MHz FSB LGA771 Active Quad-Core Processor
Brand: Intel Pages: 112
ADLINK Technology aTCA-9710 User Manual preview
aTCA-9710
Brand: ADLINK Technology Pages: 86
Primera DUP-11 User Manual preview
DUP-11
Brand: Primera Pages: 82
ICP DAS USA ET-7017-10 Quick Start Manual preview
ET-7017-10
Brand: ICP DAS USA Pages: 8

Brands by name

Popular brands

Load more brands