manualshive.com logo in svg

NXP Semiconductors MSC8113, Reference Manual

The NXP Semiconductors MSC8113 Reference Manual is an essential resource for users of this cutting-edge product. It provides in-depth guidance on its features, functionalities, and usage. Download the manual for free from our website to maximize your understanding and optimize your experience with the MSC8113.

Share
Download
background image

MSC8113 Reference Manual, Rev. 0

Freescale Semiconductor

11-1

SQBus

11

All SC140 cores can use the SQBus to fetch program code from an external memory on the 
60x-compatible system bus. This feature is useful for applications needing more program 
memory than the internal memory. The bus runs at the SC140 core frequency and allows data bus 
accesses of up to 128-bit reads and 64 bit writes. The SQBus is also typically used to configure 
the MSC8113 device. Each SC140 core can access the IPBus through the SQBus for configuring 
modules such as the DSI, timers, Ethernet controller, and TDM. Accessing the system bus 
through the SQBus, an SC140 core can configure the DMA controller, the memory controller, 
and other modules. It can access the M1 memory of another extended core. Moreover, an SC140 
core can access other devices on the system. For example, it can configure the DMA controller of 
yet another MSC8113 device on the system or directly access the M1 and M2 memories of that 
device.

The SQBus is a multi-master, multi-slave bus. The three SC140 cores are the masters of this bus. 
The slaves are the IP master for accesses to the IPBus and the system bus interface for accesses to 
the system bus. The IP master forwards accesses from the SQBus and from the local bus to the 
IPBus. When there are simultaneous requests from both the local bus and the SQBus, the SQBus 
receives higher priority and wins the arbitration. As Figure 11-1 shows, the SQBus connects the 
three extended cores through their QBuses to the system bus and to the IPBus. The bus is highly 
optimized for sharing resources between multiple SC140 cores. The SQBus arbitration model is 
exactly the same as that for MQBus (see Section 10.1, MQBus Arbitration Model).

Access to addresses 0x01F80000–0x01FFFFFF are forwarded to the IP master. All other SQBus 
accesses are forwarded to the system bus interface. No pipeline is allowed when different slaves 
are accessed. If an access to slave A wins the arbitration and there is already an open access to 
slave B, then the access to slave A waits until the access to slave B completes before it executes.

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8113

GE Mini Field Agent User Manual preview
Mini Field Agent
Brand: GE Pages: 87
NEC IE-78K0-NS-P04 User Manual preview
IE-78K0-NS-P04
Brand: NEC Pages: 72
NEC ELECTRA ELITE IPK II Programming Manual preview
ELECTRA ELITE IPK II
Brand: NEC Pages: 617
NEC VERSA DOCK - SERVICE Installation Manual preview
VERSA DOCK - SERVICE
Brand: NEC Pages: 8
Harman Kardon CITATION 7.0 Owner'S Manual preview
CITATION 7.0
Brand: Harman Kardon Pages: 66
PaloAlto Networks PA-7500 Quick Start Manual preview
PA-7500
Brand: PaloAlto Networks Pages: 3
Quantum LightSpeed Appliance QLS250 Owner'S Manual preview
LightSpeed Appliance QLS250
Brand: Quantum Pages: 12
mikroElektronika CAN SPI click Quick Start Manual preview
CAN SPI click
Brand: mikroElektronika Pages: 3
Profile LS901-E1 Instruction Manual preview
LS901-E1
Brand: Profile Pages: 6
Industrex M43ic Instruction Manual preview
M43ic
Brand: Industrex Pages: 51
STMicroelectronics ST62GP-EMU2 HDS2 Series User Manual preview
ST62GP-EMU2 HDS2 Series
Brand: STMicroelectronics Pages: 58
Arduino ABX00061 Reference Manual preview
ABX00061
Brand: Arduino Pages: 25
Divio SRA311-008P8 Series Installation Manual preview
SRA311-008P8 Series
Brand: Divio Pages: 4
uneron eSOM3735z Quick Start Manual preview
eSOM3735z
Brand: uneron Pages: 13
Smacq Technologies PCI-1232 User Manual preview
PCI-1232
Brand: Smacq Technologies Pages: 22
Lanpro LP-F22 Series Assembling Instructions preview
LP-F22 Series
Brand: Lanpro Pages: 3
Lefroy Brooks M1-5100 Installation, Operating, & Maintenance Instructions preview
M1-5100
Brand: Lefroy Brooks Pages: 10
SIIG ExpressCard 11-in-1 Reader/Writer Quick Installation Manual preview
ExpressCard 11-in-1 Reader/Writer
Brand: SIIG Pages: 8

Brands by name

Popular brands

Load more brands