manualshive.com logo in svg

NXP Semiconductors LPC29 Series, User Manual

The NXP Semiconductors LPC29 Series includes a range of high-performance microcontrollers suitable for a variety of applications. You can easily access the user manual for this series for free by downloading it from manualshive.com. This manual provides detailed instructions on operating and optimizing your LPC29 device.

Share
Download
background image

DR

AFT 

DR

AFT 

DRAFT 

DR

D

RAFT 

DRAFT 

DRA

FT DRAF

D

RAFT DRAFT DRAFT DRAFT DRAFT D

DRAFT 

D

RAFT DRA

FT DRAFT DRAFT DRAFT DRA

UM10316_0

© NXP B.V. 2008. All rights reserved.

User manual

Rev. 00.06 — 17 December 2008 

286 of 571

NXP Semiconductors

UM10316

Chapter 19: LPC29xx Universal Asynchronous Receiver/Transmitter

•

The UnIIR ABTOInt interrupt will get set if the interrupt is enabled (UnIER ABToIntEn 
is set and the auto-baud rate measurement counter overflows).

•

The UnIIR ABEOInt interrupt will get set if the interrupt is enabled (UnIER ABEOIntEn 
is set and the auto-baud has completed successfully).

The auto-baud interrupts have to be cleared by setting the corresponding UnACR 
ABTOIntClr and ABEOIntEn bits.

Typically the fractional baud-rate generator is disabled (DIVADDVAL = 0) during 
auto-baud. However, if the fractional baud-rate generator is enabled (DIVADDVAL > 0), it 
is going to impact the measuring of UARTn Rx pin baud-rate, but the value of the UnFDR 
register is not going to be modified after rate measurement. Also, when auto-baud is used, 
any write to UnDLM and UnDLL registers should be done before UnACR register write. 
The minimum and the maximum baudrates supported by UARTn are function of 
BASE_UART_CLK (UARTCLK), number of data bits, stop bits and parity bits.

(1)

4.12.2 Auto-baud modes

When the software is expecting an ”AT" command, it configures the UARTn with the 
expected character format and sets the UnACR Start bit. The initial values in the divisor 
latches UnDLM and UnDLM don‘t care. Because of the ”A" or ”a" ASCII coding 
(”A" = 0x41, ”a" = 0x61), the UARTn Rx pin sensed start bit and the LSB of the expected 
character are delimited by two falling edges. When the UnACR Start bit is set, the 
auto-baud protocol will execute the following phases:

1. On UnACR Start bit setting, the baud-rate measurement counter is reset and the 

UARTn UnRSR is reset. The UnRSR baud rate is switch to the highest rate.

2. A falling edge on UARTn Rx pin triggers the beginning of the start bit. The rate 

measuring counter will start counting BASE_UART_CLK cycles optionally pre-scaled 
by the fractional baud-rate generator.

3. During the receipt of the start bit, 16 pulses are generated on the RSR baud input with 

the frequency of the (fractional baud-rate pre-scaled) UARTn input clock, 
guaranteeing the start bit is stored in the UnRSR.

4. During the receipt of the start bit (and the character LSB for mode = 0) the rate 

counter will continue incrementing with the pre-scaled UARTn input clock 
(BASE_UART_CLK).

5. If Mode = 0 then the rate counter will stop on next falling edge of the UARTn Rx pin. If 

Mode = 1 then the rate counter will stop on the next rising edge of the UARTn Rx pin.

6. The rate counter is loaded into UnDLM/UnDLL and the baud-rate will be switched to 

normal operation. After setting the UnDLM/UnDLL the end of auto-baud interrupt 
UnIIR ABEOInt will be set, if enabled. The UnRSR will now continue receiving the 
remaining bits of the ”A/a" character.

ratemin

2

UART

×

CLK

16

215

×

---------------------------------------

UART

n

baudrate

UART

CLK

16

2

databits

paritybits

stopbits

+

+

+

(

)

×

------------------------------------------------------------------------------------------------------------

≤

≤

ratem

=

=

Summary of Contents for LPC29 Series




























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LPC29 Series

GE 400 Series Installation Instructions preview
400 Series
Brand: GE Pages: 2
Samwontech TEMP2000 Series Installation Manual preview
TEMP2000 Series
Brand: Samwontech Pages: 91
Wang 2236 Product/Maintenance Manual preview
2236
Brand: Wang Pages: 68
NAVITAS TSE Series Installation Manual preview
TSE Series
Brand: NAVITAS Pages: 14
AAF MicroTech II UV05 Operation & Maintenance Manual preview
MicroTech II UV05
Brand: AAF Pages: 50
LMI Technologies Liquitron DP5000-01A Instruction Manual preview
Liquitron DP5000-01A
Brand: LMI Technologies Pages: 28
Procom DGC-6D Operating Instructions Manual preview
DGC-6D
Brand: Procom Pages: 10
Wilo AlarmControl 1 Installation And Operating Instructions Manual preview
AlarmControl 1
Brand: Wilo Pages: 128
MOBA MOBA-Matic MMC-1000 User Manual preview
MOBA-Matic MMC-1000
Brand: MOBA Pages: 172
Progres Agrónic 7000 Installation Instructions preview
Agrónic 7000
Brand: Progres Pages: 2
fadini Elpro S40 Manual preview
Elpro S40
Brand: fadini Pages: 40
Eaton xComfort CJAU-01 Series Assembly Instructions preview
xComfort CJAU-01 Series
Brand: Eaton Pages: 4
Datapath VSN400 Series Quick Start Manual preview
VSN400 Series
Brand: Datapath Pages: 16
Collcomm NCS-C151 Instruction Manual preview
NCS-C151
Brand: Collcomm Pages: 16
LevelOne WAB-8011 Quick Installation Manual preview
WAB-8011
Brand: LevelOne Pages: 11
Delta NC10EB Quick Start Manual preview
NC10EB
Brand: Delta Pages: 9
Allen-Bradley Compact GuardLogix 5370 User Manual preview
Compact GuardLogix 5370
Brand: Allen-Bradley Pages: 210
Pego 200NDIN3RK User And Maintenance Manual preview
200NDIN3RK
Brand: Pego Pages: 32

Brands by name

Popular brands

Load more brands