LXNAV LX80xx User Manual Download

Page: 62 / 192

Operating Modes

Version 6.03, May 2017

Page 62 of 192

5.1.6.9

Rain Radar

If the Wi-Fi module is installed,

rain radar

menu is also available.

During flight, there is a possibility to get real time rain radar pictures, if Wi-fi module is

connected to the 3g hotspot and if the hotspot has mobile signal.

Show rain radar

will automatically show the radar picture layer over the map.

Opacity

defines the layer transparency over the map and

zoom level

sets when the layer can be

seen.

Max age

defines time since the last rain picture was received.

Animation

is showing

how the rain is moving over the map. Last picture can also be frozen and the duration can

be set by

freeze latest frame

5.1.6.10

Misc

Statistics thermals count and button settings can be set here.

Screen button appearance can be set by

button timeout

time. For newest instruments

proximity buttons can be used. Proximity will be detected after touch of a button if

Use

proximity

is ticked. Also

button font size

can be set here.

Summary of Contents for LX80xx

































































































































































































Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands

LXNAV LX80xx, User Manual

Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands