LXNAV LX80xx User Manual Download

Page: 88 / 192

Operating Modes

Version 6.03, May 2017

Page 88 of 192

See installation manual for details on wiring of Bridge 232.

Once bridge 232 is plugged into 485 bus, Bridge Sn.:SNxxxx will appear in Hardware menu.

First functionality must be defined. Based on functionality, dialog will change and display

related items for selected functionality.

NMEA output

define baud rate at which NMEA sentences will be transmitted. Select

desired NMEA sentences. NMEA data is exactly the same as described in chapter 5.1.12.12.

Radio bridge

is used to operate radio through main display unit. First type of connected

radio must be selected. At the moment following types are supported: KRT2, Trig TY91/92,

ATR833, Becker 620X. Support for other types is in progress. Please consult LXNAV for more

details.

Check

Auto set target frequency

, if you want to automatically select frequency, when

new target is selected in navigational mode. Ticking

show target warnings

will trigger

warnings generated from the device (example: radio is too hot).

Transponder bridge

can operate the transponder with the main unit. Supported

transponders are: Becker BXP6402 and Trig TT21/22.

ICAO code, ID and SQUAWK could be set and send from LXxxxx device to the transponder.

It can also show target warnings from transponder.

Summary of Contents for LX80xx

































































































































































































Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands

LXNAV LX80xx, User Manual

Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands