LXNAV LX80xx Page 180 User Manual Download

Page: 180 / 192

Options

Version 6.03, May 2017

Page 180 of 192

Options

10.1

Flarm

Before using Flarm it is highly recommended to read the Flarm user manual which

can be downloaded from

www.flarm.com

. Respect all limitations listed in this

document.

Flarm is a collision avoidance system developed by Flarm Technologies from Switzerland.

The Flarm module consists of following main parts: GPS receiver, microcontroller unit, radio

transceiver pressure altimeter and optional an external indicator. All electronic parts are

integrated into the main display unit cabinet. An exception is the radio communication

antenna and the Flarm External Display. Some input is possible via the external display.

In case, that unit has no built Flarm, external Flarm connection is possible using

LX5flarm or LX5PF cable for power Flarm.

10.1.1

Installation

For more detailed instructions on installation, please refer to installation manual.

The position of the radio communication antenna is extremely important as a bad

installation will reduce the system range dramatically. It is highly recommended to install

the antenna on the top of the instrument panel with a suitable aluminium round plate

having a diameter of about 12 cm used as a back plane and an approximately 10 cm long

rubber antenna used as the radiator. The metal plate may be mounted outside or inside of

the instrument panel. If carbon is used, use only the top mounting variant.

Summary of Contents for LX80xx

































































































































































































Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands

LXNAV LX80xx, User Manual

Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands