LXNAV LX80xx User Manual Download

Page: 116 / 192

Operating Modes

Version 6.03, May 2017

Page 116 of 192

5.5.3

Third Navigation Page

The third page is a combination of first navigational page and side view.

Side view is showing lateral view from glider towards selected goal. Terrain below glider is

displayed including glider projected track based on glide ratio in grey colour. Yellow and

magenta lines are showing requested glide ratio to goal based on zero MacCready setting

and current MacCready setting.

5.5.4

Fourth Navigation Page

The fourth navigational page is combination of FLARM radar screen and some additional
altitude data.

The internal pressure sensor altitude is shown as

AltIGC

AltInv

shows the altitude in

opposite units to those defined in the

Units

setup.

OAT

is the outside temperature,

Pot.Temp

is the potential temperature and

Battery

displays the current voltage

The estimated time of arrival and estimated time established are displayed at the bottom

part of page.

Summary of Contents for LX80xx

































































































































































































Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands

LXNAV LX80xx, User Manual

Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands