LXNAV LX80xx User Manual Download

Page: 63 / 192

Operating Modes

Version 6.03, May 2017

Page 63 of 192

5.1.7

Sounds*

In the Sounds setup page audio settings, voice settings and alarms settings for the vario

unit can be modified.

Volume can be also controlled using upper left rotary knob. Rotating it will

directly change volume for sounds, which is currently being played. For example,

if voice message is being played, voice message volume will be set. If alarm is

beeping, alarm volume will be set. In speed to fly mode, speed to fly volume is

set and in climb mode, vario volume is set.

When button

VOLUMES

is pressed a menu will appear, where it is possible to set

up all volumes at same time.

Summary of Contents for LX80xx

































































































































































































Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands

LXNAV LX80xx, User Manual

Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands