manualshive.com logo in svg

LXNAV LX80xx, User Manual, Page: 28 / 192

Share
Download
LXNAV LX80xx User Manual Download Page 28

Operating Modes

 

 

Version 6.03, May 2017 

 

 

Page 28 of 192

 

 

5

 

Operating Modes 

The  main  display  unit  has  seven 

modes

  or 

main  menus

.    All  of them  are  selectable  by 

rotating  the  upper-right  knob  which  is  also  called 

MODE  selector

.    The  diagram  below 

shows the mode structure of the LX9000 running in portrait screen. 

 

 

Airport Mode

, navigation and selection airports. 

 

Waypoint Mode

, navigation, selection and editing waypoints. 

 

Task Mode

, Navigation, selection and editing task. 

 

Statistics Mode

 shows statistical data for flight in progress or logbook. 

 

Setup

 mode is used to configure the whole system. 

 

Information  Mode

  displays  GPS  status,  altitude,  flight  level  and  height,  sunrise  and 

sunset  or  position  report  to  selectable  point  or  satellite  sky  view  (only  if  there  is  no 

internal flarm). 

 

Near Mode

 displays a list of all landable waypoints and airports. 

 
The  Navigation  modes  and  statistics  mode  have  additional  pages  which  are  accessible  by 

rotating the bottom-right knob also called the 

PAGE selector

. 

Summary of Contents for LX80xx

































































































































































































Reviews:

No comments