LXNAV LX80xx User Manual Download

Page: 68 / 192

Operating Modes

Version 6.03, May 2017

Page 68 of 192

5.1.8

Optimization

During flight the system optimises the flown path according to OLC or FAI rules. Use this

dialogue to change the way instrument performs this optimisation.

Number of points defines the type of optimisation. Use five for OLC optimisation. Use the

value three for FAI free flight optimisation.

Optimisation will not take into account the 10 km distance between turn points

which is required by FAI rules.

The FAI triangle group defines the rules for FAI triangles and these rules can bend a little if

you do not want to fly marginal triangles.

Check

Reset optimization on engine run

to reset optimization counter each time engine

is started.

5.1.9

Warnings

There are four types of warnings available. Airspace warnings are shown when approaching

a particular airspace zone. Altitude warnings are shown when approaching to a defined

altitude, Flarm warnings are triggered when conflicting traffic is in the vicinity, Time Alarms

are raised at defined time interval to remind pilot to do specific task, Gear warning is

triggered at pre-defined above ground level altitude setting and Waypoint warning will be

given at set distance to Waypoint.

Use this dialogue to setup the behaviour of warnings.

Summary of Contents for LX80xx

































































































































































































Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands

LXNAV LX80xx, User Manual

Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands