LXNAV LX80xx User Manual Download

Page: 171 / 192

Flying with the System

Version 6.03, May 2017

Page 171 of 192

A message will appear. If you confirm this with

YES

the task will be advanced to the next

turn point and it will recalculate the task taking the optimal fix as the task point.

7.2.4

Entering Assigned Area

Most probably when entering an assigned area auto advance is going to be turned off. The

message

“Inside zone”

will be shown and buttons

CLOSE

and

NEXT

will appear in the

lower row. Pressing the

CLOSE

button will dismiss the inside zone message. The task will

be auto advanced to the next point when leaving the assigned area. If you want to auto

advance to the next turn point earlier you may always press the

NEXT

button in task mode

(see 7.2.3).
If

NEXT

is pressed the task is advanced to the next turn point.

When flying in an assigned area it is NOT important when you will advance to next

turn point. The system is always taking into account the most optimal fix inside

the assigned area for the total distance calculation.

7.2.5

Moving Point Inside Assigned Area

If at least one observation zone is defined as an assigned area, it is possible to move the

point within this area. Moving the point will increase or decrease the total task length.

Select the

MOVE

action within task mode. A dialogue with the current assigned area will be

shown.

Summary of Contents for LX80xx

































































































































































































Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands

LXNAV LX80xx, User Manual

Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands