LXNAV LX80xx User Manual Download

Page: 106 / 192

Operating Modes

Version 6.03, May 2017

Page 106 of 192

5.2

Information Mode

Information mode consists of four pages; GPS status page, position report page, satellite

sky view page and network status page. Use the PAGE selector knob or the up/down arrow

to toggle pages.

5.2.1

GPS Status Page

GPS status, altitude, flight level and height are shown on this page. Sunrise and sunset are
calculated for the current position. In the upper-right corner the current FLARM status is

shown. TX means FLARM is transmitting data to others and the number indicates how

many other FLARM devices are within range.

Press

START

button to start running stopwatch. Press

STOP

button to stop running

stopwatch. If you press the

MARK

button a new waypoint will be created with the current

latitude, longitude and elevation based on the terrain database. The waypoint name is

generated from the current date and time separated by the minus character and preceded

by an underscore.

Summary of Contents for LX80xx

































































































































































































Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands

LXNAV LX80xx, User Manual

Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands