manualshive.com logo in svg

LXNAV LX80xx, User Manual, Page: 95 / 192

Share
Download
LXNAV LX80xx User Manual Download Page 95

Operating Modes

 

 

Version 6.03, May 2017 

 

 

Page 95 of 192

 

 

5.1.11.12

 

NMEA Output 

The main display unit is capable of transmitting position data sentences in NMEA format for 

use by other devices. 

 

Port

  defines  on  which  serial  interface  data  will  be  transmitted. 

Baud  rate

  defines 

transmission speed. Data is divided into three groups: 

 

GPS data

 will output all GPS-related data such as time, longitude and altitude. 

 

LXNAV  data

  will  output  all  variometer-related  data  such  as  vario,  MacCready  and 

ballast. 

 

Flarm data

 will output all Flarm-related data. 

 

 

 

 

PDA can be connected to the LX80/90xx system through the NMEA bridge or on 

the EXT.(PC) port. 

 

NMEA data is available also on Flarm display port on main display unit and rear 

display unit at 19200bps. However only Flarm data and GPS data. 

5.1.11.13

 

Engine * 

Use  this  menu,  when  the  system  is  installed  into  glider  with  engine.  The  current  engine 

noise level is shown as a progress bar.  If external MOP sensor is installed also MOP level 

will be shown. 

Summary of Contents for LX80xx

































































































































































































Reviews:

No comments