LXNAV LX80xx User Manual Download

Page: 87 / 192

Operating Modes

Version 6.03, May 2017

Page 87 of 192

5.1.11.5

LCD and USB-D Vario indicator*

This is type of the older vario indicator. An LCD vario indicator or USB-D vario indicator

consists of:



Needle



Two numerical displays (upper and lower).



Labels and indicators.

These following functions can be set (see next picture):



Needle:

vario needle (Vario, SC, Netto or Relative).



SC Ring

: Displays speed command at all times.



Upper Numeric Display

Integrator, time, flight time, task remaining time. Upper line;

the parameter displayed can be configured in both Vario and SC modes.



Vario Mode Indicator

: Shows current flight mode (vario or speed command).



Lower Numeric Display

: Altitude (NN altitude), Distance (distance to the navigation

point), Glide diff. (final glide altitude difference), Speed (TAS), Leg speed (speed on

leg), QNH (ft) (NN altitude in ft), Flight levels. Lower line; the parameter displayed can

be configured in both Vario and SC modes.

The labels will automatically be displayed depending on the current function. The BAT

warning will be displayed when the supply voltage is below 11 volts.

LXNAV is highly recommending upgrading old LCD vario indicators to latest

technology vario indicator unit. Please contact local dealer or LXNAV for more
details.

5.1.11.6

Bridge 232*

Bridge 232 is an external device which is sold separately and is used to output NMEA data or

to connect radio or transponder to the system.

Summary of Contents for LX80xx

































































































































































































Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands

LXNAV LX80xx, User Manual

Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands