LXNAV LX80xx User Manual Download

Page: 98 / 192

Operating Modes

Version 6.03, May 2017

Page 98 of 192

5.1.11.15

Flaps*

When flap sensor is installed, use this menu to set flaps position. Use page selector to select

desired flap position. Press

SET

button to set position. Continue with procedure for all flap

positions.

When all flap positions are set, a green dot will be displayed with current flap position.

If flap labels are not set yet, press EDIT button to name flap label. Flap labels must me

entered with increasing speed range. It is recommended that flaps labels are set together

with speed range in Polar and Glider setup. See Chapter 0 for more details.

It is also possible to toggle between cruise and climb mode using flap sensor in this case
there is no need to define digital input for SC.

5.1.11.16

Battery Types*

This menu defines type of battery being used. Selecting type of battery is important in order

to correctly show low battery warnings.

Use

Type

combo to select appropriate type of battery (Lead Acid, LiFe, LiPo, custom). You

can see empty, low and full voltage for the selected type of battery. In case of voltage drop,

because of cable lengths, you can set up voltage

offset

there to the

current voltage

measured.

Summary of Contents for LX80xx

































































































































































































Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands

LXNAV LX80xx, User Manual

Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands