LXNAV LX80xx User Manual Download

Page: 26 / 192

System Description

Version 6.03, May 2017

Page 26 of 192

4.3.9

Pull down menu

Pull down menu is used to select one of the options. Press button several times to select

appropriate item of turn PAGE selector knob. Pull down menu will automatically close after

few seconds.

4.4

Switching off

Please use one of the following recommended methods for shutting down the LX90xx

system:

Method 1

Press the button with the

OFF

label which is displayed in navigational modes. See Chapter

5.5 for more details. A message to confirm shutdown will be shown.

Method 2

Press the button with the

OFF

symbol for approximately 4 seconds. The OFF message will

be displayed and the instrument will shut down. When the message appears you must

release the power button.

Summary of Contents for LX80xx

































































































































































































Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands

LXNAV LX80xx, User Manual

Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands