LXNAV LX80xx User Manual Download

Page: 40 / 192

Operating Modes

Version 6.03, May 2017

Page 40 of 192

Multiple files can be selected. All checked files will be shown on the graphics page and used

in the near mode calculation, if the waypoint is of the proper type (airport or outlanding

place). However, only one file can be the active file. The active file is primary used for task

creation. Task can be loaded only from the active file.

When a waypoint file from USB or SD card is selected, it will be available only, if

SD card or USB stick is inserted in main display unit.

Selecting waypoint files on SD card or USB allows you to create portable profiles,

which can be transferred from one device to another device.

Press the

ACTIVE

button to mark the selected file as active.

Press the

DELETE

button to remove the selected file from the internal storage of main

display unit.

If WiFi option is presented, button

TO MAIL

will be visible. Press this button to send

selected file to email.

If waypoints files from the SD or USB are selectable, button LOAD is visible. Press the

LOAD

button to upload selected waypoint file to internal storage.

If waypoints file from internal storage is selected button SAVE is visible. Press the

SAVE

button to save waypoints to the SD Card or USB stick. The save dialogue will be opened.

Summary of Contents for LX80xx

































































































































































































Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands

LXNAV LX80xx, User Manual

Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands