LXNAV LX80xx User Manual Download

Page: 190 / 192

Options

Version 6.03, May 2017

Page 190 of 192

For more detailed instructions on installation, please refer to installation manual.

10.6

Flap sensor

The flap encoder is connected to the system via the RS485 bus. It is physically mounted

near the flap mechanism. The flap encoder is very sensitive and accurate and can detect

very small movements.

Please refer to flap sensor manual for details about installation. For configuration on the

main display unit see Chapter 5.1.11.14.

For more detailed instructions on installation, please refer to installation manual.

10.7

Secondary Vario Indicators

An unlimited number of secondary vario indicators can be connected to the system bus.

RS485 splitting units should be used to extend the bus capacity. The functionality of

secondary units depends on settings made in setup (see chapter 5.1.11.1.3).

Each unit has two female nine-pin connectors on the back side. Both connectors are 100%

pin to pin compatible and it doesn’t matter which will be used. Any other RS485 bus

operated unit can be any time connected to a free connector port of the vario indicator.

Summary of Contents for LX80xx

































































































































































































Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands

LXNAV LX80xx, User Manual

Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands