LXNAV LX80xx User Manual Download

Page: 178 / 192

Firmware Update

Version 6.03, May 2017

Page 178 of 192

already consists from the SD card adapter and the micro SD card, then you can

simply ignore this message), press OK.



Copying of the firmware will be performed



When you get a message with action, please take the micro SD card from the

LX80/90xx and insert into the V8/V80



V8/V80 will detect the micro SD card and will automatically ask you: UPDATE?...

confirm it with the middle button on the V8/80 which will perform a restart and a SW

update.



Once the update is successfully booted, you can check your latest version in the

SETUP->ABOUT menu in the V8/V80 vario unit.



On the LX80/90xx you can terminate the message by clicking the OK button.

A micro SD card adapter is needed for a manual V8/V80 update.

8.2.2

Manual vario update

Download the vario file from

www.lxnav.com

and put it on the sd card.

Start the system, insert the SD card and go to the Setup->Password menu option.

Enter password

89891

and press

ENTER

The system will automatically search for an update file. If more than one update file is

found a selection dialogue will appear.

Select appropriate update file and wait until update will finish.

Summary of Contents for LX80xx

































































































































































































Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands

LXNAV LX80xx, User Manual

Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands