LXNAV LX80xx User Manual Download

Page: 25 / 192

System Description

Version 6.03, May 2017

Page 25 of 192

Rotating the zoom selector changes colour transparency. Transparency is very important for

fill colours which are used for airspace zones, observation zones and FAI area. If a fill

colour is not transparent (0%), all other map items will not be seen through it. If a fill

colour is 100% only the solid border will be drawn.

Press PICK button to define colour more precisely. A colour dialog will open, where you can

select colour from HSV circle or enter values for red, green and blue colour.

4.3.7

Font Selector

Using the font selector it is possible to define a font colour and style for a selected item.

Turn the PAGE selector knob (page-selector) to change the font style. Text is also rendered

in the selected font style. Turn the ZOOM selector knob (zoom-selector) to change the font

colour.

Press PICK button to define colour more precisely. A colour dialog will open, where you can

select colour from HSV circle or enter values for red, green and blue colour.

4.3.8

Line pattern Selector

Using line pattern selector it is possible to define width and pattern of line. Turn the PAGE

selector knob (page-selector) to change the width of line. Turn the ZOOM selector knob

(zoom-selector) to change the line pattern. Results are immediately visible on selected

item.

Summary of Contents for LX80xx

































































































































































































Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands

LXNAV LX80xx, User Manual

Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands