LXNAV LX80xx User Manual Download

Page: 175 / 192

Firmware Update

Version 6.03, May 2017

Page 175 of 192

Firmware Update

Firmware updates of the main display unit, vario unit or vario indicator can be easily carried

out using the SD Card/USB key. Please visit our webpage

www.lxnav.com

and send us a

request for the firmware update.

Update can be also done through Wi-Fi (if internet connection is established and Wi-fi

module is enabled on the LX system).

You can also subscribe to a newsletter to receive news about the system automatically.

8.1

Updating main display firmware

We will send you an update file and update code. The update code is a string six letters

long and the update file has the

.lx8000

.lx8080

.lx9000

.lx9050

.lx9070

extension. To proceed with the firmware update copy the update file to a SD card or USB

stick and insert it into the main display unit.

Start the main display unit and go to the Setup->Password menu option.

Enter password

89891

and press

ENTER

The system will automatically search for an update file. If more than one update file is

found a selection dialogue will appear.
After the update file is selected an update code must be entered.

Enter the update code which was sent to you.

Summary of Contents for LX80xx

































































































































































































Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands

LXNAV LX80xx, User Manual

Search results

Summary of Contents for LX80xx

Reviews:

Related manuals for LX80xx

Brands by name

Popular brands