Juniper JUNOSE 11.0.X MULTICAST ROUTING Configuration Manual Download Page 684 | Manualshive

Page: 684 / 788

background image

■

During installation, Service Manager precompiles the service definition and
extracts the definition file’s timestamp.

■

After you install the service definition, you can use the definition to create service
sessions for subscribers.

■

To update an existing service definition, you make changes to the original macro
file on your computer, copy the updated file to NVS, and install the updated file.
All subsequent service sessions use the new service definition file. However,
currently active service sessions continue to use the original definition file until
the sessions are deactivated, then reactivated.

■

Example 1—Installing

host1(config)#

service-management install tiered.mac

■

Example 2—Uninstalling

host1(config)#

no service-management install tiered.mac

■

Example 3—Updating

! update the original macro file on the remote system
! copy the updated macro file to the router
host1#

copy boston:/serviceDefs/triplePlay/tiered.mac tiered.mac

host1#

configure terminal

! install the updated service definition on the router
host1(config)#

service-management install tiered.mac

■

Use the

no

version to uninstall a service definition.

■

See service-management install

Referencing Policies in Service Definitions

In Profile Configuration mode, policy interface commands for IP and L2TP allow
attachments to be merged into any existing merge-capable attachment at an
attachment point. Merged policies are dynamically created. Service Manager can
request that multiple interface profiles be applied or removed at an interface as part
of service activation or deactivation. Service Manager also specifies whether or not
the attachments created from these interface profiles persist on subsequent reloads.

Service Manager can specify whether a component policy attachment is non-volatile.
If the interface where the component policy is attached is volatile, then policy
management makes the attachment volatile even when the Service Manager specifies
otherwise. A non-volatile interface can have both volatile and non-volatile component
policy attachments. The merged policy that is created is the merge of all component
policies attached at a given attachment point regardless of their volatility. The merged
policy and its attachments are always volatile and reconstructed on each reload
operation.

For further details on merging policies, see the

Merging Policies

chapter in

JUNOSe

Policy Management Configuration Guide

.

644

■

Referencing Policies in Service Definitions

JUNOSe 11.0.x Broadband Access Configuration Guide

«
...
682
683
684
685
686
...
»

Summary of Contents for JUNOSE 11.0.X MULTICAST ROUTING





















































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JUNOSE 11.0.X MULTICAST ROUTING

RS232 interface for GT47 embedded apps UART

Brand: Sony Ericsson Pages: 14

Brand: PS Audio Pages: 6

SNAP DEPLOY 2.0 -

Brand: ACRONIS Pages: 68

DATA SYNCHRONIZER - UPDATE 1

Brand: Novell Pages: 9

2950C-24 - Catalyst Switch - Stackable

Brand: Cisco Pages: 18

CONFERENCING EXTENSIONS - ADMINISTRATOR GUIDE FOR MICROSOFT EXCHANGE

Brand: Cisco Pages: 61

Cisco mds 9124 - fabric switch

Brand: Cisco Pages: 9

Brand: Cisco Pages: 16

Cisco MDS 9020 - Fabric Switch

Brand: Cisco Pages: 22

Brand: Cisco Pages: 13

Cisco mds 9124 - fabric switch

Brand: Cisco Pages: 3

Brand: Cisco Pages: 7

Brand: Cisco Pages: 74

Craft Works Interface

Brand: Cisco Pages: 32

Catalyst Series Switch 2940

Brand: Cisco Pages: 82

Catalyst Series Switch 2940

Brand: Cisco Pages: 28

Brand: Cisco Pages: 58

CCNA NETWORK SIMULATOR

Brand: Cisco Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands