Service Manual
vii
Ɣ
Be sure to install circuit breakers (ground fault interrupter, isolating switch, molded case circuit
EUHDNHUDQGVRRQZLWKWKHVSHFL¿HGFDSDFLW\(QVXUHWKDWWKHZLULQJWHUPLQDOVDUHWLJKWHQHGVHFXUHO\
WRUHFRPPHQGHGWRUTXHVSHFL¿FDWLRQV
Ɣ
Clamp electrical wires securely with a cable clamp after all wiring is connected to the terminal block.
In addition, run wires securely through the wiring access channel.
Ɣ
When installing the power lines, do not apply tension to the cables. Secure the suspended cables at
regular intervals, but not too tightly.
Ɣ
Make sure that the terminals do not come into contact with the surface of the electrical box. If the
terminals are too close to the surface, it may lead to failures at the terminal connection.
Ɣ
Turn OFF and disconnect the unit from the power source when handling the service connector. Do not
open the service cover or access panel to the indoor or outdoor units without turning OFF the main
power supply.
Ɣ
$IWHUFHDVLQJRSHUDWLRQEHVXUHWRZDLWDWOHDVW¿YHPLQXWHVEHIRUHWXUQLQJRIIWKHPDLQSRZHU
switch. Otherwise, water leakage or electrical breakdown may result. Disconnect the power source
completely before attempting any maintenance for electrical parts. Check to ensure that no residual
voltage is present after disconnecting the power source.
Ɣ
Do not clean with, or pour water into, the controller as it could cause electric shock and/or damage the
unit. Do not use strong detergent such as a solvent. Clean with a soft cloth.
Ɣ
Check that the ground wire is securely connected. Do not connect ground wiring to gas piping, water
piping, lighting conductor, or telephone ground wiring.
Ɣ
If a circuit breaker or fuse is frequently activated, shut down the system and contact your service
contractor.
Ɣ
Perform all electrical work in accordance with this manual and in compliance with all regulations and
safety standards.
Ɣ
'RQRWRSHQDVHUYLFHDFFHVVFRYHURUSDQHORIDQLQGRRURURXWGRRUXQLWZLWKRXW¿UVWWXUQLQJ2))WKH
power at the main power supply.
Ɣ
Residual voltage can cause electric shock. At all times, check for residual voltage after disconnecting
from the power source before starting work on the unit.
Ɣ
Use a Ground Fault Circuit Interrupter (GFCI) to reduce the chance of an electric shock.
Summary of Contents for YVAHP072B31S
