Service Manual
1-371
INSTALLATION
NOTES:
1. After at least three minutes time after start-up, change the optional setting.
2. When changing the “CF” setting, (change of louver swing angle), restore the power supply or allow the louver to
make one complete swing fully in the auto swing mode to apply the optional setting.
3. Optional settings differ between indoor and outdoor units.
Check to ensure that the unit is or is not equipped with optional settings.
4. Record the setting conditions for each optional setting in the “Setting” column of the table.
5. The above optional functions with a corresponding “X” that denotes that the individual setting can change the
condition only when “All Rooms” is set.
No.
Items
Optional Function
Individual
Setting
Setting
Condition
Contents
Setting
101
P3
Sensor Temperature
×
00
01
02
03
Inlet
Outlet
Controller Thermo
Remote Sensor
102
P4
Display of Sensor Temperature
×
00
01
Not Available
Available
103
P5
Setting Temperature when Operation
Mode is FAN
×
00
01
Display
Not Available
104
P6
Select Power Saving Button
×
00
01
Available
Not Available
105
P7
Menu Screen Transition Prohibited
×
00
01
Not Available
Available
106
P8
Not Prepared
-
-
Not Used
107
P9
Not Prepared
-
-
Not Used
108
PA
Daylight Saving Time
×
00
01
1 hr
2 hrs
109
PB~PC Not Prepared
-
-
Not Used
*1: The “02”, “03”, and “04” settings may not be available according to the type of indoor unit.
When connecting multiple indoor units, create separate settings.
*2: In case of Duct type models, 00: Increasing fan speed 1 (standard),
01: Increasing fan speed 2 (high static pressure), 02: Standard (low static pressure)
*3: When the Thermistor for the Controller is selected:
00: Control by the Thermistor for Indoor Inlet
01: Control by the Thermistor for the Controller
02: Control by Average Value of the Thermistor for the Indoor Inlet and the Thermistor for the Controller
When the Remote Sensor is connected:
00: Control by Average Value of the Thermistor for the Indoor Inlet and the Remote Sensor
01: Control by the Remote Sensor
02: Control by Average Value of the Thermistor for the Indoor Inlet and the Remote Sensor
*4: E1 to E4: Setting for the total heat exchanger
*5: In case that the set temperature is changed and kept within the set time at “F4”, the temperature automatically
changes to “F5” and “F6”. (In case that the set temperature is out of range at “F5” and “F6”, it is applied within
upper and lower limit for the set temperature.)
*6: Applicable to fan, cooling and dry operation modes.
*7: Applicable to heating operation mode.
*8: Operation is stopped by pressing the “ ” (On/Off) switch for 3 seconds.
*9: The sensor value at “C8” will be indicated. When the thermistor for controller is used, the average value of the
thermistor for the controller and the thermistor for the indoor inlet will be displayed.
*10: When the unit is restarted by the controller, the temperature setting automatically changes to the temperature of “F5”
or “F6”.
Summary of Contents for YVAHP072B31S
