manualshive.com logo in svg

Geehy SEMICONDUCTOR APM32F030x4x6x8xC, User Manual

Share
Download
Geehy SEMICONDUCTOR APM32F030x4x6x8xC User Manual Download Page 171

 

www.geehy.com                                                                                                                                              Page  170

 

Field 

Name 

R/W 

Description 

1 

CC1IFLG 

RC_W0 

Capture/Compare Channel1 Interrupt Flag 

When the capture/compare channel 1 is configured as output: 

0: No matching occurred 
1: The value of TMRx_CNT matches the value of TMRx_CC1 

When the capture/compare channel 1 is configured as input: 

0: Input capture did not occur 
1: Input capture occurred 

When a capture event occurs, the bit is set to 1 by hardware, and it 

can be cleared by software or cleared when reading TMRx_CC1 
register. 

8:7 

Reserved 

9 

CC1RCFLG 

RC_W0 

Capture/compare Channel1 Repetition Capture Flag 

0: Repeat capture does not occur 
1: Repeat capture occurs 

The value of the counter is captured to TMRx_CC1 register, and 

CC1IFLG=1; this bit is set to 1 by hardware and cleared by 
software only when the channel is configured as input capture. 

15:10 

Reserved 

 

Control event generation register (TMRx_CEG) 

Offset address: 0x14 
Reset value: 0x0000 

Field 

Name 

R/W 

Description

 

0 

UEG 

W 

Update Event Generate 

0: Invalid 

1: Initialize the counter and generate the update event 
This bit is set to 1 by software, and cleared by hardware. 

Note: When an update event is generated, the counter of the prescaler will be 

cleared, but the prescaler factor remains unchanged.

 

In the count-down mode, 

the counter reads the value of TMRx_AUTORLD; in center-aligned mode or 

count-up mode, the counter will be cleared. 

1 

CC1EG 

W 

Capture/Compare Channel1 Event Generation 
0: Invalid 

1: Capture/Compare event is generated 

This bit is set to 1 by software and cleared automatically by hardware. 

If Channel 1 is in output mode: 

When CC1IFLG=1, if CC1IEN and CC1DEN bits are set, the corresponding 

interrupt and DMA request will be generated. 

If Channel 1 is in input mode: 

The value of the capture counter is stored in TMRx_CC1 register; configure 

CC1IFLG=1, and if CC1IEN and CC1DEN bits are also set, the corresponding 
interrupt and DMA request will be generated; at this time, if CC1IFLG=1, it is 

required to configure CC1RCFLG=1. 

15:2 

Reserved 

 

Capture/Compare mode register 1 (TMRx_CCM1) 

Offset address: 0x18 
Reset value: 0x0000 
The timer can be configured as input (capture mode) or output (compare mode) 
by CCxSEL bit. The functions of other bits of the register are different in input 
and output modes, and the functions of the same bit are different in output mode 
and input mode. The OCx in the register describes the function of the channel in 
the  output  mode,  and  the  ICxx  in  the  register  describes  the  function  of  the 
channel in the input mode. 

Output compare mode: 

Field 

Name 

R/W 

Description 

1:0 

CC1SEL 

R/W 

Capture/Compare Channel 1 Select 
This bit defines the input/output direction and the selected input pin. 

Summary of Contents for APM32F030x4x6x8xC












































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands