manualshive.com logo in svg

Exar XRT86VL38, Manual

The Exar XRT86VL38 user manual is available for free download on manualshive.com. This comprehensive manual provides detailed instructions, troubleshooting tips, and useful insights for maximizing the potential of your XRT86VL38. Accessible in a few clicks, this manual will assist you in harnessing the full power of your XRT86VL38.

Share
Download
background image

xr

PRELIMINARY

XRT86VL38

REV. P1.0.6 

OCTAL T1/E1/J1 FRAMER/LIU COMBO

18

TxMSYNC0/

TxINCLK0

TxMSYNC1/

TxINCLK1

TxMSYNC2/

TxINCLK2

TxMSYNC3/

TxINCLK3

TxMSYNC4/

TxINCLK4

TxMSYNC5/

TxINCLK5

TxMSYNC6/

TxINCLK6

TxMSYNC7/

TxINCLK7

B10

A17

C24

L24

AC21

AD16

AC8

AF2

A9

B15

E18

K20

U17

AB14

AB3

W5

I/O

(Continued)

DS1/E1 Multiplexed High-Speed Backplane Interface (TxINCLK as 
input)

In the multiplexed high-speed interface mode, this pin is used as the trans-
mit input clock for the high-speed backplane interface to input high-speed 
data applied to TxSERn pin.  Users must configure the TxINCLK as as 
input in the multiplexed high-spped backplane mode. 

The multiplexed modes supported are Bit-multiplexed 12.352MHz (DS1 
only), Bit-multiplexed 16.384MHz,  Byte-multiplexed HMVIP 16.384MHz, 
and Byte-multiplexed H.100 16.384MHz.

In DS1 only 12.352MHz bit-multiplexed high-speed backplane mode, 
TxINCLK is an input clock signal at 12.352MHz 

In DS1/E1 16.384MHz bit-multiplexed high-speed backplane mode, TxIN-
CLK is an input clock signal at 16.384MHz 

In DS1/E1 HMVIP 16.384MHz byte-multiplexed high-speed backplane 
mode, TxINCLK is an input clock signal at 16.384MHz 

In DS1/E1 H.100 16.384MHz byte-multiplexed high-speed backplane 
mode, TxINCLK is an input clock signal at 16.384MHz 

N

OTES

:

1.

In DS1 16.384MHz multiplexed high-speed back plane mode, the 
DS-0 data is mapped into an E1 frame by ignoring every fourth 
time slot (don’t care).

2.

These 8 pins are internally pulled “Low” for each channel.

TxCHCLK0

TxCHCLK1

TxCHCLK2

TxCHCLK3

TxCHCLK4

TxCHCLK5

TxCHCLK6

TxCHCLK7

A12

E17

B26

J22

AD22

AE16

AD10

AB2

C12

A16

E19

G22

AA19

Y13

V11

V5

O

Transmit Channel Clock Output Signal

The exact function of this pin depends on whether or not the XRT86VL38 
is configured to use the transmit fractional/signaling interface to input frac-
tional data.  

If transmit fractional/signaling interface is not used:

If transmit fractional interface is not used, this pin indicates the boundary 
of each time slot of an outbound DS1/E1 frame.  In T1 mode, each of 
these output pins is 192kHz clock which pulses "High" whenever the 
Transmit Payload Data Input Interface block accepts the LSB of each of 
the 24 time slots.  In E1 mode, each of these output pins is 256kHz clock 
which pulses "High" whenever the Transmit Payload Data Input Interface 
block accepts the LSB of each of the 32 time slots. The Terminal Equip-
ment can use this clock signal to sample the TxCHN0 through TxCHN4 
time slot identifier pins to determine which time slot is being processed.

If transmit fractional/signaling interface is used:

If transmit fractional interface is used, TxCHCLK is the fractional interface 
clock which either outputs a clock signal for the time slot that has been 
configured to input fractional data, or outputs an enable signal so that frac-
tional data can be clocked into the device using the TxSERCLK pin. 

If the TxSYNCFRD bit (from register 0xn120) is set to ‘0’, the TxCHCLK 
output pin will output a gapped fractional clock that can be used by termi-
nal equipment to input fractional payload data using the falling edge of the 
clock.  

If the TxSYNCFRD bit (from register 0xn120) is set to ‘1’, the TxCHCLK 
output pin will output an enable signal and fractional payload data is 
clocked into the chip using the un-gapped TxSERCLK pin.

N

OTE

:  Transmit fractional interface can be enabled by programming to bit 

4 - TxFr1544/TxFr2048 bit from register 0xn120 to ‘1’.

TRANSMIT SERIAL DATA INPUT

S

IGNAL

 N

AME

420 P

KG

B

ALL

#

484 P

KG

B

ALL

 #

T

YPE

D

ESCRIPTION

Summary of Contents for XRT86VL38



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XRT86VL38

Sun Microsystems 5945532 User Manual preview
5945532
Brand: Sun Microsystems Pages: 58
POWERCOLOR Red Devil RX 5600 Series Quick Installation Manual preview
Red Devil RX 5600 Series
Brand: POWERCOLOR Pages: 14
Sangoma B700 FlexBRI Installation Manual preview
B700 FlexBRI
Brand: Sangoma Pages: 6
TwinMOS CRW7A3 Quick Installation Manual preview
CRW7A3
Brand: TwinMOS Pages: 2
ICP DAS USA PCIe-S114 Quick Start Manual preview
PCIe-S114
Brand: ICP DAS USA Pages: 8
ICP DAS USA PCIe-LM4 User Manual preview
PCIe-LM4
Brand: ICP DAS USA Pages: 53
ICP DAS USA PCI-D96SU User Manual preview
PCI-D96SU
Brand: ICP DAS USA Pages: 40
ICP DAS USA PCI-1202 Series User Manual preview
PCI-1202 Series
Brand: ICP DAS USA Pages: 123
ICP DAS USA PCI-1002H User Manual preview
PCI-1002H
Brand: ICP DAS USA Pages: 44
ICP DAS USA PCIe-S118 Quick Start Manual preview
PCIe-S118
Brand: ICP DAS USA Pages: 8
NETGEAR 11AC-AR9880 Product Installation Manual preview
11AC-AR9880
Brand: NETGEAR Pages: 4
ADLINK Technology PCIe-9842 User Manual preview
PCIe-9842
Brand: ADLINK Technology Pages: 44
Aaeon PER-U00A User Manual preview
PER-U00A
Brand: Aaeon Pages: 23
IBM TURBOWAYS 25 Hardware Installation Manual preview
TURBOWAYS 25
Brand: IBM Pages: 44
IBM EtherJet 10BASE-T ISA Adapter Manual preview
EtherJet 10BASE-T ISA Adapter
Brand: IBM Pages: 109
Asus Audio Card Xonar D2 Installation Manual preview
Audio Card Xonar D2
Brand: Asus Pages: 80
Asus Audio Card Xonar D2 User Manual preview
Audio Card Xonar D2
Brand: Asus Pages: 84
Vantec UGT-S220 Installation Manual preview
UGT-S220
Brand: Vantec Pages: 2

Brands by name

Popular brands

Load more brands