manualshive.com logo in svg

Exar XRT86VL38, Manual

The Exar XRT86VL38 user manual is available for free download on manualshive.com. This comprehensive manual provides detailed instructions, troubleshooting tips, and useful insights for maximizing the potential of your XRT86VL38. Accessible in a few clicks, this manual will assist you in harnessing the full power of your XRT86VL38.

Share
Download
background image

XRT86VL38

PRELIMINARY

xr

OCTAL T1/E1/J1 FRAMER/LIU COMBO

REV. P1.0.6 

227

4

COFA ENB

R/W

0

Change of FAS Framing Alignment (COFA) Interrupt Enable

This READ/WRITE bit-field permits the user to either enable or dis-
able the “Change in FAS Framing Alignment (COFA)” Interrupt, 
within the XRT86VL38 device. If the user enables this interrupt, then 
the Receive E1 Framer block will generate an interrupt when it 
detects a Change of FAS Framing Alignment Signal (e.g., the FAS 
bits have appeared to move to a different location within the incom-
ing E1 data stream).

0 – Setting this bit to ‘0’ will disable the “Change of FAS Framing 
Alignment (COFA)” Interrupt.

1 – Setting this bit to ‘1’ will enable the “Change of FAS Framing 
Alignment (COFA)” Interrupt.

3

IF ENB

R/W

0

Change of In-Frame Condition Interrupt Enable

This READ/WRITE bit-field permits the user to either enable or dis-
able the “Change of In-Frame Condition” Interrupt, within the 
XRT86VL38 device. If the user enables this interrupt, then the 
Receive E1 Framer block will generate an interrupt in response to 
either one of the following conditions.

1.

The instant that the Receive E1 Framer block declares the 
Loss of Framing Alignment (LOF) condition.

2.

The instant that the Receive E1 Framer block clears the Loss 
of Framing Alignment (LOF) condition.

The “Change of In-Frame Condition” Interrupt can be enabled or 
disabled, as described below.

0 – Setting this bit to ‘0’ will disable the “Change of In-Frame Condi-
tion” Interrupt.

1 – Setting this bit to ‘1’ will enable the “Change of In-Frame Condi-
tion” Interrupt.

2

FMD ENB

R/W

0

Frame Mimic Detection Interrupt Enable

This READ/WRITE bit-field permits the user to either enable or dis-
able the “Frame Mimic Detection” Interrupt, within the XRT86VL38 
device. If the user enables this interrupt, then the Receive E1 
Framer block will generate an interrupt when it detects the presence 
of Frame mimic bits (i.e., the payload bits have appeared to mimic 
the framing bit pattern within the incoming E1 data stream).

0 – Setting this bit to ‘0’ will disable the “Frame Mimic Detection” 
Interrupt.

1 – Setting this bit to ‘1’ will enable the “Frame Mimic Detection” 
Interrupt.

T

ABLE

 131: F

RAMER

 I

NTERRUPT

 E

NABLE

 R

EGISTER

 E1 M

ODE

R

EGISTER

 532 E1 M

ODE

                    F

RAMER

 I

NTERRUPT

 E

NABLE

 R

EGISTER

 (FIER)                         H

EX

 A

DDRESS

: 0

X

nB05

B

IT

F

UNCTION

T

YPE

D

EFAULT

D

ESCRIPTION

-O

PERATION

Summary of Contents for XRT86VL38



























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XRT86VL38

E-Mu 404 Quick Start Manual preview
404
Brand: E-Mu Pages: 12
Datapath ImageDP4 Manual preview
ImageDP4
Brand: Datapath Pages: 2
SIIG ID-P20111-S1 Quick Installation Manual preview
ID-P20111-S1
Brand: SIIG Pages: 20
Insignia NS-MCR17MUSB Quick Setup Manual preview
NS-MCR17MUSB
Brand: Insignia Pages: 2
National Instruments NI Vision NI PCI-1424 User Manual preview
NI Vision NI PCI-1424
Brand: National Instruments Pages: 28
Broadcom BCM94312HMGB User Manual preview
BCM94312HMGB
Brand: Broadcom Pages: 39
Velleman PCUSBGO2 User Manual preview
PCUSBGO2
Brand: Velleman Pages: 19
ADLINK Technology EGX-MXM-RTX5000 User Manual preview
EGX-MXM-RTX5000
Brand: ADLINK Technology Pages: 33
StarTech.com PCI1394MP Instruction Manual preview
PCI1394MP
Brand: StarTech.com Pages: 8
ACS ACR30S Driver Installation Manual preview
ACR30S
Brand: ACS Pages: 22
Blackberry PRD-09695-004 - SMART Card Reader Manual preview
PRD-09695-004 - SMART Card Reader
Brand: Blackberry Pages: 28
Edimax N-9210TX-64 User Manual preview
N-9210TX-64
Brand: Edimax Pages: 9
impro XTT909-1-0-GB-XX Installation Manual preview
XTT909-1-0-GB-XX
Brand: impro Pages: 8
Farpointe Data EM-30 Quick Start Manual preview
EM-30
Brand: Farpointe Data Pages: 2
Farpointe Data CONEKT PCR-620L-OSDP Quick Start Manual preview
CONEKT PCR-620L-OSDP
Brand: Farpointe Data Pages: 2
ATI Technologies X1900 - Radeon XTX 512 MB PCIE Video Card User Manual preview
X1900 - Radeon XTX 512 MB PCIE Video Card
Brand: ATI Technologies Pages: 160
Sun Microsystems XVR-2500 Installation And User Manual preview
XVR-2500
Brand: Sun Microsystems Pages: 84
Sun Microsystems Netra CP2000 Series Parts Installation And Removal Manual preview
Netra CP2000 Series
Brand: Sun Microsystems Pages: 24

Brands by name

Popular brands

Load more brands