manualshive.com logo in svg

Exar XRT86VL38, Manual

Share
Download
Exar XRT86VL38 Manual Download Page 163

xr

PRELIMINARY

XRT86VL38

REV. P1.0.6 

OCTAL T1/E1/J1 FRAMER/LIU COMBO

152

2

BER[1]

R/W

0

Bit Error Rate

This READ/WRITE bit-field is used to insert PRBS bit error at the 
rates presented at the table below. The exact function of this bit 
depends on whether PRBS switch function is enabled or not. (Test 
Register 2 (TR2), Address 0xn121, bit 3 set to 1). 

If the PRBS switch function is disabled, bit error will be inserted by 
the T1/E1 transmit framer out to the line interface if this bit is 
enabled. 

If the PRBS switch function is enabled, bit error will be inserted by 
the T1/E1 receive framer out to the receive backplane interface if 
this bit is enabled. 

1

BER[0]

R/W

0

0

UnFramedPRBS

R/W

0

Unframed PRBS Pattern

This READ/WRITE bit-field enables or disables unframed PRBS/
QRTS pattern generation (i.e. All timeslots and framing bits are all 
PRBS/QRTS data). The exact function of this bit depends on 
whether PRBS switch function is enabled or not. (Test Register 2 
(TR2), Address 0xn121, bit 3 set to 1). 

If PRBS switch function is disabled, T1/E1 Transmit Framer will gen-
erate an unframed PRBS 15 or QRTS pattern to the line side if this 
bit is enabled.

If PRBS switch function is enabled, T1/E1 Receive Framer will gen-
erate an unframed PRBS 15 or QRTS pattern to the receive back-
plane interface if this bit is enabled.

0 - Setting this bit to ‘0’ will enable an unframed PRBS/QRTS pat-
tern generation to the line interface or to the receive backplane inter-
face

1 - Setting this bit to ‘1’ will disable an unframed PRBS/QRTS pat-
tern generation to the line interface or to the receive backplane inter-
face

T

ABLE

 61: DS1/E1 T

EST

 R

EGISTER

 2(TR2) 

R

EGISTER

 34                                                 DS1/E1 T

EST

 R

EGISTER

 2 (TR2)                                                     0

XN

121

B

IT

F

UNCTION

T

YPE

D

EFAULT

D

ESCRIPTION

-O

PERATION

BER[1:0]

BIT ERROR RATE

00

Disable Bit Error insertion to the transmit output 
or receive backplane interface

01

Bit Error is inserted to the transmit output or 
receive backplane interface at a rate of 1/1000 
(one out of one Thousand)

10

Bit Error is inserted to the transmit output or 
receive backplane interface at a rate of 1/
1,000,000 (one out of one million)

11

Disable Bit Error insertion to the transmit output 
or receive backplane interface

Summary of Contents for XRT86VL38



























































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands